KI Engage Task Chair User Manual

Required
Tools
Disassembly Instructions
Material Type:
Warning: This drawing format requires special non-standard fonts!!
Make sure the appropriate font files are installed!!!
TT Humanst 521 BT Light
O HelveticaLTStd-Cond
O HelveticaLTStd-LightCond
Engage Task Chair, Engage Stool, Piretti 2000 Task Chair, Piretti 2000 Stool
Page 1 of 3Rev. 1 P0033-0080
A. Steel B. Plastic C. Foam D. Fabric
KI · 1330 Bellevue Street · P.O. Box 8100 · Green Bay, WI 54308-8100 · 1-800-424-2432 · www.ki.com
Procedure:
1. Pry off the rear shrouds from the backrest.
2. Pry the Back Shroud from the Back Assembly.
3. Remove the screws holding the backrest to the steel backrest
support and remove the backrest.
(continued next page)
General Notes:
1. Disassembly time: 30-45 minutes
2. This procedure assumes basic familiarity with hand tools and
furniture terminology: no specialized training is required
3. All materials removed and disassembled shall be sorted and
segregated with like materials and disposed of or recycled
according to recycling availability or waste acceptance
4. For items to be recycled, refer to KI's End of Life Recycling
Matrix and KI's End of Life Recovery Options Matrix, available
at www.ki.com
All fasteners not explicitly tagged
are Material Type A: Steel
Procedure:
1. Remove the screws holding the backrest onto the back sup-
ports and remove the backrest.
2. Pry off the cover under the seat to expose the seat support
plate. Remove the screws holding the support plate to the seat
and remove the seat.
3. Remove the screws holding each arm cap to the back sup-
ports and remove the arm caps.
4. Pry out the end caps holding the arms onto the torsion tube
and remove the outer bushings. Rotate each inner bushing so
that the slot underneath is aligned with the pin. Push back on
the support which will allow the pin to drop out. Pull the sup-
ports and inner bushings away from the frame and pull out the
leaf springs.
5. Pry out the caps from the seat frame tubes underneath the seat.
6. Pry out the casters and caster bushings from the chair base.
See Sheet 3
See Sheet 2
Gloves
Safety Glasses
Pry Bar
Philips Screwdriver
Putty Knife
Hex Socket Wrench
Rubber Mallet
Flat Screwdriver
Channel Lock Pliers
Torx Screwdriver
Robertson Screwdriver
Robertson Screwdriver
Allen Wrench
B
B
D
C
B
A
B

KI Engage Task Chair Specifications

General

Product Type	Task Chair
Brand	KI
Model	Engage
Backrest	Yes
Base	5-star base
Weight Capacity	300 lbs
Adjustable Seat Depth	Yes
Tilt Lock	Yes
Tilt Mechanism	Synchro-tilt
Adjustable Lumbar Support	Yes
Material	Fabric or Vinyl

Summary

Task Chair Disassembly Procedure

Remove Rear Backrest Shrouds

Pry off the rear shrouds from the backrest.

Detach Back Shroud

Pry the back shroud from the back assembly.

Remove Backrest from Support

Remove screws holding the backrest to the steel support.

Remove Armrests and Seat

Unscrew armrests and seat from the support mechanism.

Remove Control Knobs and Shrouds

Pry off plastic control knobs, handles, and shrouds.

Separate Base and Cylinder

Tap bottom of cylinder and lift base to remove plastic parts.

Discard Components

Dispose of backrest, seat, base, and plastic components.

Recycle Components

Recycle seat support, back support (J-bar), and cylinder.