KI WorkUp RT User Manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
WorkUp
®
Adjustable Table
Model RT
April 2019
Tools Required
• #3 Phillips Screwdriver
• 5 mm Hex Key
Note: Before discarding any
packaging, confirm all components
received against the packing list.
Table assembly should be done on a
clean flat floor.
Note: When tightening the M8
screws, first twist in all four screws
“finger tight”, then tighten the screws
one quarter turn at a time using
a diagonal tightening pattern as
shown in Detail A. Repeat the
diagonal pattern until all four screws
are tight (Figure 1 & Detail A).
Feet-to-Columns Assembly
1. Set the column on end with the
smaller (inner) square tube on the
floor. The threaded holes visible
on the end of the column will be in
a rectangular (not square) pattern
(Figure 1).
2. Place the foot over the column
end so the column fits into the
square hole in the foot. The slotted
holes in the foot should line up with
the four holes in the column end. If
not the foot needs to be removed and
repositioned at 90 degrees
(Figure 1).
3. Attach the foot using four
M8 x 20 mm screws and four 8 mm
flat washers, tightening each screw
one quarter turn at a time in a
diagonal pattern until all four screws
are tight (Figure 1 & Detail A).
4. Thread leveling glides into the holes
at the ends of the foot (Figure 1).
Note: If the roller foot option was
purchased, one foot will have
pre-assembled rollers.
5. Repeat steps 1 through 4 for the
second foot and column (Figure 1).
Detail
A
Figure 1
leveling glide
foot
column
M8 x 20 mm
screw
flat
washer

KI WorkUp RT Specifications

General

Brand	KI
Model	WorkUp RT
Category	Indoor Furnishing
Language	English

Summary

Tools Required

Feet-to-Columns Assembly

Set Column on Floor

Place the column on its end with the smaller square tube on the floor, aligning threaded holes.

Position Foot on Column

Place foot over column end, fitting column into square hole, aligning slotted holes.

Attach Foot to Column

Secure foot using four M8 screws and washers, tightening diagonally.

Install Leveling Glides

Thread leveling glides into the holes at the ends of the foot.

Repeat for Second Foot

Repeat steps 1-4 for the second foot and column assembly.

Attach Tabletop Support to Columns

Align Tabletop Support Holes

Align tabletop support holes with the foot/column assembly holes.

Secure Tabletop Support

Attach tabletop support with four M8 screws, tightening diagonally.

Attach Second Column Assembly

Attach the second foot/column assembly in the same manner.

Attach Tabletop to Base Assembly

Prepare Tabletop

Place tabletop top-side down on a soft, protective surface.

Position Tabletop Support

Place tabletop support with columns onto the tabletop's drilled face.

Align Tabletop and Support Holes

Shift tabletop support to align holes in the tabletop with those in the support.

Secure Tabletop

Attach tabletop support to tabletop using #12 x 1" tapping screws.

Install Wire Trough (Optional)

Mount Wire Trough

Align wire trough mounting holes to tabletop holes and secure with screws.

Operating the Table

Invert Table Safely

Carefully invert the table to its upright position with two or more people.

Level the Table

Adjust leveling glides to ensure the table is level.

Adjust Table Height Upward

Lift one side of the worksurface at a time to adjust height.

Adjust Table Height Downward

Raise table to upper stops, then lower slowly to the bottom position.