KI HF User Manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Assembly Instructions
WorkUp Adjustable Table
Model HF
April 2017
Tools Required
• #2 Phillips Screwdriver
• #3 Phillips Screwdriver
• 5mm Hex Key
Note: Before discarding any
packaging confirm all components
received against the packing list.
Table assembly should be done on a
clean flat floor.
Note: When tightening the
M8 x 18mm screws, first twist in
all four screws “finger tight”, then
tighten the screws one quarter turn
at a time using a diagonal tightening
pattern as shown in Detail A. Repeat
the diagonal pattern until all four
screws are tight (Figure 1 &
Detail A).
Feet To Columns Assembly
1. Set the column on end with the
smaller (inner) square tube on the
floor. The threaded holes visible
on the end of the column will be in
a rectangular (not square) pattern
(Figure 1).
2. Place the foot over the column end
so the column fits into the square
hole in the foot. The slotted holes
in the foot should line up with the
four holes in the column end. If not
the foot needs to be removed and
repositioned at 90 degrees
(Figure 1).
3. Attach the foot using four
M8 x 18mm screws and four 8mm
flat washers, tightening each screw
one quarter turn at a time in a
diagonal pattern until all four screws
are tight (Figure 1 & Detail A).
4. Thread leveling glide into the holes
at the ends of the foot (Figure 1).
Note: If the roller foot option was
purchased, one foot will have
pre-assembled rollers.
5. Repeat steps 1 through 4 for the
second foot and column (Figure 1).
Detail A
Motor-Operated Furnishing
-FOR COMMERICAL USE ONLY-
Figure 1
foot
column
M8 x 18mm
screw
leveling
glide
flat
washer

KI HF Specifications

General

Brand	KI
Model	HF
Category	Indoor Furnishing
Language	English

Summary

Feet To Columns Assembly

Column Preparation and Foot Alignment

Prepare column, align foot with threaded holes, and reposition if necessary.

Attach Foot to Column

Secure the foot to the column using M8 screws and flat washers in a diagonal tightening pattern.

Install Leveling Glide

Thread leveling glide into the designated holes at the ends of the foot.

Repeat Assembly for Second Leg

Repeat the entire foot-to-column assembly process for the second leg.

Columns to Worksurface Support Assembly

Position and Align Worksurface Support

Hold column assemblies upright and align worksurface support holes with column holes.

Attach Worksurface Support to Columns

Secure worksurface support to columns using M8 screws in a diagonal tightening pattern.

Attach Second Foot/Column Assembly

Attach the second foot/column assembly to the worksurface support in the same manner.

Worksurface Assembly

Prepare Table Top for Mounting

Place table top upside down on a soft protective surface to prevent scratching.

Position Worksurface Support on Table Top

Place worksurface support with columns onto the table top, aligning with pre-drilled holes.

Attach Table Top to Support

Secure the table top to the worksurface support using #12 x 1" tapping screws.

Electric Controls Installation

Attach Keypad

Mount the keypad to the underside of the table top using #10 x 11/16" tapping screws.

Mount Control Box

Position and attach the control box to the underside of the table top using #12 x 1" screws.

Install Optional Wire Trough

If optional, install plastic wire trough using its double-sided tape between steel angles.

Wire Trough Installation

Determine Wire Trough Mounting Location

Center wire trough over supports or adjust based on table top depth (22-36 inches).

Secure Wire Trough to Table Top

Align mounting holes and secure the wire trough using six #10 x 5/8" pan head screws.

Electrical Cables Connection

Connect Leg and Extension Cables

Connect extension cables to leg cables, then to control box sockets (M1, M2).

Connect Keypad Cable

Connect the keypad cable to the HS socket on the control box, ensuring proper alignment.

Secure Cables with Clamps

Use cable clamps and screws to secure column and keypad cables to the worksurface near the control box.

Grounding Instructions

Initializing and Operating the Table

Invert and Position Table

Carefully invert the table to its upright position with assistance, then adjust leveling glides.

Manage Loose Cables

Tuck loose cables into the open side of the plastic wire trough.

Connect Power Cord

Insert the power cord into the socket on the control box.

Initialize System

Plug into AC outlet, press and hold up/down arrows for five seconds to zero the system.

Adjust Table Height

Use keypad arrows to adjust table height, ensuring clear space around pinch areas.

Important Safety Instructions