Kidde Gemini II - Appendix F Special Requirements for Canadian Systems Conforming to ULC-S527-99; General; Operation; Main Control Panel

F-1November 2002 06-235975-001
Kidde Gemini II System
APPENDIX F
SPECIAL REQUIREMENTS FOR CANADIAN SYSTEMS
CONFORMING TO ULC-S527-99
F-1 GENERAL
This chapter describes the operation and installation of the
features unique to Main Control Panel P/N 84-322001-010
and Remote Hazard Unit P/N 84-322002-005.
F-2 OPERATION
F-2.1 Main Control Panel
The P/N 84-322001-010 Main Control Panel (MCP) con-
tains a second LED Display Module that provides additional
indication of alarms, troubles, and supervisory events cor-
responding to each protected zone.
Table F-1. Secondary LED Display Module Messages
DELNOITCNUFNOITACIDNI
11enoZrotceteD-MLAdeR
22enoZrotceteD-MLAdeR
3esaeleRlaunaM-MLAdeR
4tkCwolfretaW-MLAdeR
5detavitcAtkCyrosivrepuSwolleY
61enoZrotceteD-LBTwolleY
72enoZrotceteD-LBTwolleY
8esaeleRlaunaM-LBTwolleY
9tkCwolfretaW-LBTwolleY
01tkC2#vpuS/trobA-LBTwolleY
11tkC1#vpuS-LBTwolleY
21dnuorG-LBTwolleY
31tluaFsmmoC-LBTwolleY
41rewopCAlenaP-LBTwolleY
51nOtiucriCtrobAwolleY
61decneliSlangiSwolleY
Because the display is limited to three hazards, Canadian
systems may have a maximum of two RHUs connected to
the MCP as shown in Figure F-1.
ID
TBL - COMMS FAULT
TBL - PANELAC POWER
ABORT CIRCUIT ON
SIGNAL SILENCED
ALM - WATERFLOW CKT
SUPERVISORY CKT ACTIVATED
TBL - DETECTOR ZONE 1
TBL - MANUAL RELEASE
ALM - MANUAL RELEASE
TBL - DETECTOR ZONE 2
TBL - WATERFLOW CKT
TBL - ABORT CKT
TBL - SUPERVISORY CKT
TBL - GROUND
ALM - DETECTOR ZONE 1
ALM - DETECTOR ZONE 2
ID
TBL - COMMS FAULT
TBL - PANELAC POWER
ABORT CIRCUIT ON
SIGNAL SILENCED
ALM - WATERFLOW CKT
SUPERVISORY CKT ACTIVATED
TBL - DETECTOR ZONE 1
TBL - MANUAL RELEASE
ALM - MANUAL RELEASE
TBL - DETECTOR ZONE 2
TBL - WATERFLOW CKT
TBL - ABORT CKT
TBL - SUPERVISORY CKT
TBL - GROUND
ALM - DETECTOR ZONE 1
ALM - DETECTOR ZONE 2
ID
TBL - COMMS FAULT
TBL - PANELAC POWER
ABORT CIRCUIT ON
SIGNAL SILENCED
ALM - WATERFLOW CKT
SUPERVISORY CKT ACTIVATED
TBL - DETECTOR ZONE 1
TBL - MANUAL RELEASE
ALM - MANUAL RELEASE
TBL - DETECTOR ZONE 2
TBL - WATERFLOW CKT
TBL - ABORT CKT
TBL - SUPERVISORY CKT
TBL - GROUND
ALM - DETECTOR ZONE 1
ALM - DETECTOR ZONE 2
SUPERVISORYPOWER ON ALARM
SCROLL
ALARM
SCROLL
SUP/TBL
CANCEL
ACCEPT
CONTROL
MAIN
PANEL
SILENCED
SIGNAL
TROUBLE
SILENCE
SIGNAL
CONTROLS
MENU
SYSTEM
CONTROLS
RESET
II
R
TM
R
GEMINI
Figure F-1. MCP Configured for Three Hazards
One LED Display Module (the leftmost one when viewed
from the front of the panel) is factory mounted on the MCP
and provides alarm, trouble and supervisory indications for
the MCP. Up to two additional LED Display modules may
be installed on a system, one for each RHU. Once the RHUs
have been configured and registered on the MCP as de-
scribed in Chapter 7, the MCP will automatically display
the status of RHUs 1 and 2 on the second and third dis-
plays (left to right), respectively.
Additional LED Display modules (P/N 84-322001-013) will
be required to be field-installed on the MCP to supplement
the factory mounted module for two and three-hazard sys-
tems. A two-hazard system will require one additional LED
Display Module while a three-hazard system will require
two modules.
Since the Hazard 1 LED Display Module is required to be
plugged into the Optional Relay Board socket on the MCP,
Canadian MCPs do not support the installation of ORBs.
The Hazard 2 module plugs into the Hazard 1 module while
the Hazard 3 module plugs into Hazard 2.
The display window features 3 slide-in cards that identify
each LED. Each card has a title field, allowing the user to
identify the zone. Cards corresponding to unused zones
may be reversed to show the plain black back.
firealarmresources.com