What to do if King Quest VQ4100 unit scans but does not find satellite?
If your King Quest Antenna unit scans but fails to find a satellite, it may be due to a line of sight obstruction. To resolve this, move the antenna unit to a location with a clear view of the southern sky. Additionally, press the RESET button on the power injector to initiate a new scan.
How to fix King Quest VQ4100 unit that does not scan for satellites?
If your King Quest Antenna unit isn't scanning for satellites, the issue might be related to power or the need for a reset. First, ensure the antenna unit is properly connected to the power injector and that the power injector is receiving power, indicated by a lit LED. If it's correctly connected, try pressing the RESET button on the power injector, as the antenna unit may simply need to be reset.
Why King Quest VQ4100 Antenna unit scans but there is no picture on TV?
If your King Quest Antenna unit scans, but you're not getting a picture on your TV, the problem could stem from improper connections. Verify that the antenna unit is connected to the power injector, and that the power injector is properly plugged in. Also, ensure that the powered receiver is correctly connected to both the power injector and the TV.
What to do if picture on TV goes in and out using King Quest Antenna?
If the picture on your TV is intermittently cutting in and out while using the King Quest Antenna, it's likely due to a temporary obstruction of the signal. Heavy rain or snow can cause signal loss; the reception should improve as the weather clears. Also, ensure that there are no temporary obstructions blocking the view to the southern sky, such as tree branches swaying in the wind.
Why does my King Quest Satellite TV System antenna unit scan but not find a satellite?
The antenna unit might not be finding a satellite due to a line of sight obstruction. To resolve this, move the antenna unit to ensure it has a clear view of the southern sky. Then, press the RESET button on the power injector to initiate a new scan.
What to do if my King Quest Satellite TV System antenna unit does not scan for satellites?
If the antenna unit isn't scanning for satellites, there could be a couple of reasons. First, ensure the antenna unit is properly connected to the power injector and that the power injector is receiving power—the LED should be lit. Also, try pressing the RESET button on the power injector. The antenna unit may simply need to be reset.
What to do if my King Quest Satellite TV System antenna unit scans but there is no picture on TV?
If your antenna unit scans but you're not getting a picture on your TV, it may be due to improper connections. Check that the antenna unit is connected to the power injector, and that the power injector is plugged in. Also, make sure the powered receiver is correctly connected to the power injector and the TV.
Why does the picture on my King Quest Satellite TV System go in and out?
The picture on your TV may be going in and out due to a temporary obstruction of the signal. Heavy rain or snow can cause signal loss; reception should improve as the weather clears. Also, ensure nothing is temporarily blocking the view to the southern sky, such as tree branches blowing in the wind.
What to do if King Quest Antenna unit scans but no picture on TV?
If your King Quest Antenna unit scans but you're not getting a picture on your TV, it might be due to connection issues. Ensure the antenna unit is properly connected to the power injector, and that the power injector is plugged into a power source. Also, verify that the powered receiver is connected correctly to both the power injector and your TV.
Why King Quest VQ4100 unit scans but does not find satellite?
If your King Quest antenna unit scans but fails to find a satellite, it's likely due to an obstruction blocking its line of sight. To resolve this, move the antenna unit to a location with a clear view of the southern sky. After repositioning, press the RESET button on the power injector to initiate a new scan.
Details the process of unboxing the KING Quest and applying the rubber feet for stability.
Wiring diagram and instructions for connecting the KING Quest to older model DIRECTV receivers.
Steps to configure the DIRECTV receiver and initiate the satellite scanning process.
Explains how to enable the optional alarm feature and how it functions when active.
Guidance on securing the antenna and a table of common issues and their solutions.
Procedures for physically mounting the antenna unit and routing the coaxial cables correctly.
General| Gain | 3dBi |
|---|---|
| Polarization | Vertical |
| Frequency Range | 698-2700 MHz |
| Impedance | 50 Ω |
| Operating Temperature | -40°C to +70°C |
To Next Page
