King Technology Pool Frog User Manual

Pool FROG CYCLER
MINERAL PURIFIER FOR POOLS
Instruction Manual
REPLACE
MINERAL
RESERVOIR
EVERY
SEASON.

King Technology Pool Frog Specifications

General

Brand	King Technology
Model	Pool Frog
Category	Swimming Pool Cleaners
Language	English

Summary

Pool FROG System Overview

Introduction to Pool FROG Components

Introduces the Cycler, Mineral Reservoir, FROG® BAM™, and Bac Pac as parts of the system.

Part I: POOL FROG® Cycler

The water treatment center controlling water flow, available in above ground and inground models.

Part II: POOL FROG® Mineral Reservoir

Holds minerals and fits inside the Cycler, available in different sizes. Must be replaced yearly.

Part III: FROG® BAM™

A mineral formula for preventing algae up to 90 days. Use with the POOL FROG® System.

Part IV: POOL FROG® Bac Pac

Provides low-level chlorine support for a complete system. Use Flow Control Pac when using other chlorine.

Ensuring Pool Health and Water Balance

Circulation and Water Quality Checks

Ensures adequate pool circulation and checks for metals and filter cleanliness.

Water Balance Guidelines

Provides recommended ranges for pH, alkalinity, hardness, TDS, stabilizer, and free chlorine.

Start-up and Yearly Maintenance Steps

Outlines initial steps for water balance and ongoing maintenance for a healthy pool.

Pool FROG Start-up Procedures

Initial System Setup and Shocking

Steps for adding stabilizer, shocking the pool, installing components, and initial system run.

Setting the Control Dial

Guide to setting the control dial based on pool size, pump size, and pump run time.

Pool FROG Operation and Chlorine Support

Ongoing Water Testing and Adjustments

Instructions for testing free chlorine and adjusting the control dial for optimal levels.

Pool Shocking and Chlorine Support

Guidance on pool shocking and using alternative chlorine support methods.

Replacing System Components

Replacing the Mineral Reservoir

Steps for identifying, removing, and inserting the correct POOL FROG® Reservoir.

Important Usage and Replacement Warnings

Caution to use only factory recommended parts and replacement schedules.

Cycler Maintenance Steps

Instructions on turning off pump, relieving pressure, and setting dial to Pac Removal.

Using FROG BAM for Algae Control

Installing FROG® BAM™

Steps for inserting FROG® BAM™ into the Mineral Reservoir to puncture the seal and secure the cap.

Circulating FROG® BAM™

Instructions for setting the control dial to Maximum and running the pump to circulate FROG® BAM™.

Removing and Discarding FROG® BAM™

Procedure for turning off the pump, removing the FROG® BAM™ container, and discarding it.

Using the Bac Pac for Chlorine

Preparing and Installing the Bac Pac

Steps for replacing the Flow Control Pac with the Bac Pac and securing it into the Reservoir.

Bac Pac Operation and Maintenance

Instructions for shaking the Bac Pac, replacing the cap, and setting reminders for replacement.

Troubleshooting Pool FROG Issues

Resolving Water Clarity Problems

Diagnosing and fixing issues with cloudy or colored pool water using filtration and shocking.

Addressing Algae and Chlorination

Solutions for algae growth, under-chlorination, and over-chlorination with the Bac Pac.

Fixing Cap and Dial Adjustment Issues

Resolving problems with tight caps or difficult dial adjustments using specific tools.

Pool FROG Parts Identification

Cycler Parts List (Series 5400/5600)

Detailed list of parts for the 5400/5600 series Cycler with reference numbers and quantities.

Cycler Parts List (Series 5100/5200)

Detailed list of parts for the 5100/5200 series Cycler with reference numbers and quantities.

Off-Line Installation Parts

List of additional parts included with the 5430/5630 series for off-line installations.

Cycler Maintenance and O'Ring Replacement

Replacing Control Dial O'Rings (5100/5200)

Step-by-step guide for replacing O'rings on the control dial for 5100/5200 series Above Ground Cyclers.

Replacing Control Dial O'Rings (5400/5600)

Detailed instructions for replacing O'rings on the control dial for 5400/5600 series Inground Cyclers.

Cycler Component Replacement and Winterizing

Replacing Cap O'Ring and Drain Valve

Instructions for replacing the cap O'ring and drain valve using silicone lubricant.

Pool FROG Winterization Procedures

Steps for preparing the system for winter, including turning off the pump, removing parts, and draining.

Storing Winterized Components

Guidance on storing the Bac Pac and discarding the Mineral Reservoir after winterization.

Above Ground Filter Installation (Models 5100/5200)

Installing Nipple and Hose Adapter

Steps for applying Teflon tape and installing the nipple and hose adapter to the filter return.

Connecting Cycler and Flex Hose

Instructions for connecting the Cycler to the nipple and attaching the flex hose with a clamp.

Check Valve Recommendation

Recommendation to install a check valve for optimal performance, especially with a chlorine Bac Pac.

Above Ground Base Installation (Models 5100/5200)

Connecting Cycler to Pump and Filter

Steps for applying Teflon tape and screwing adapters into the Cycler ends for connection.

Attaching Flex Hose and Clamps

Procedure for attaching the filter and return sections of flex hose to the Cycler adapters using clamps.

Mounting the Cycler on a Base

Guidance on mounting the Cycler on a base using screws for better stability.

Inground Installation (Models 5400/5600)

Installation Location and Precautions

Advice on installation location, avoiding copper pipe, and not installing off-line.

Cutting Pipe and Applying PVC Cement

Steps for measuring, cutting pipe, and applying PVC cement to bushings and pipe ends.

Securing Cycler to Base

Instructions for inserting PVC pipe into bushings and securing the Cycler to a treated wood base.

Off-line Installation (Models 5430/5630)

Off-line Installation Guidelines

Guidance on installing off-line when in-line space is insufficient, avoiding heaters and in-line configurations.

Connecting Adapters and Bushings

Steps for applying sealants, screwing male adapters into the Cycler, and inserting reducer bushings.

Attaching Elbows and Tubing

Procedure for screwing elbows into bushings and attaching tubing with clamps.

Completing Off-line Installation

Attaching Tubing and Scoops

Instructions for cutting tubing, attaching elbows, scoops, and gaskets to the pipe and clamps.

Securing Cycler to Base

Recommendation for using Phillips pan head screws to secure the Cycler to a treated wood base.

Check Valve for Chlorine Bac Pac

Advice to install a corrosion-resistant check valve if using a chlorine Bac Pac.

Special Inground Installation Scenarios

High GPMS and In-floor Cleaners

Guidance for high water flow and when an in-floor cleaner is included with the pool.

Pool and Spa Combination Management

Recommendations for pool and spa combinations and managing back pressure.

Limited Two-Year Warranty Information

Obtaining Warranty Service and Exclusions

Procedure for warranty service, including delivery and proof of purchase, and what the warranty does not cover.

Important Cautions and Product Limitations

Warnings about shock treatment, control dial settings, excess trichlor, and misuse of the product.