KNEGT 404G2 Series - User Manual

Questions and Answers

M
Melissa MatthewsAug 26, 2025
Why is the steering so heavy on my KNEGT 404G2?
- S
  Sarah DavisAug 26, 2025
  If the steering on your KNEGT Tractor feels too heavy, several factors could be responsible. The great pump might be supplying insufficient oil, experiencing an internal leak, or the filter net in the oil case could be blocked; check the pump and clean the filter net. Air in the steering system or oil with foam can also cause this issue; eliminate the air and inspect. Finally, the steering oil case might not be supplying enough oil; replenish the oil to the specified level.
C
Corey SuttonAug 27, 2025
Why can't I fully disengage the clutch on my KNEGT Tractor?
- R
  Regina WrightAug 27, 2025
  If the clutch on your KNEGT Tractor cannot be separated completely, it may be because the pedal’s free path is too large, and the working path is too small. In this case, adjust the pedal free travel as specified. Another reason may be that the driven disk warps too much. You should rectify or replace it with a new one. Finally, the release finger of the diaphragm spring may not be at the same plane and need replacement.
W
warrenwilliamAug 28, 2025
What causes the front tires to wear so quickly on my KNEGT Tractor?
- D
  Donna CameronAug 28, 2025
  Serious wear on the front tires of your KNEGT Tractor can be caused by several factors. The front wheel rim or supporter may be seriously deformed, requiring correction. Improper front wheel toe-in adjustment can also lead to this issue, so adjust the toe-in. Additionally, worn steering knuckles and pins of the oil cylinder should be replaced. Finally, insufficient air pressure and engaging the front axle during transport can contribute to tire wear; check and inflate the tires and disconnect the front axle.
D
Douglas WellsAug 28, 2025
Why is there noise coming from the gearbox of my KNEGT 404G2?
- R
  Ryan BaileyAug 28, 2025
  Humming or slapping noises in the gearbox of your KNEGT Tractor can arise from several issues. The gear might be heavily abraded, the tooth face peeling off, or the gear teeth broken, necessitating gear replacement. The bearing could also be seriously abraded or damaged, requiring bearing replacement. Additionally, improper clearance of bevel transmission should be adjusted. Finally, insufficient lubricating oil or oil that doesn't meet requirements should be addressed by filling in enough oil or replacing the lubricating oil.
K
Kelly GrantAug 29, 2025
Why doesn’t the PTO work on my KNEGT 404G2?
- R
  Robert GriffithAug 29, 2025
  If the PTO on your KNEGT Tractor isn’t working, several issues could be the cause. Check the PTO button to ensure it is not broken. Also, inspect the circuit for any problems. If the valve is broken, it will need to be replaced. Finally, make sure the PTO is properly engaged.
D
Diane BaileyAug 30, 2025
Why does my KNEGT 404G2 Tractor shiver when starting?
- D
  David HarrisAug 30, 2025
  If your KNEGT Tractor shivers when starting, it could be due to the friction disk and the driven disk being stained with oil; clean them. Alternatively, the friction disk might be broken, requiring replacement, or the driven disk may be warped, also requiring replacement.
H
Hannah MontgomeryAug 23, 2025
Why is the clutch slipping on my KNEGT 404G2?
- L
  Lawrence CollinsAug 23, 2025
  Clutch slip in your KNEGT Tractor can occur if the clutch disk or plate is stained with oil. Clean them with gasoline and eliminate the oil leakage. It can also happen if the clutch disk is unevenly worn or seriously abraded, requiring replacement. Insufficient or no free path can also cause this issue, so readjust according to the requirements. Finally, a deformed driven disk can also cause clutch slip, and it should be replaced.
K
kayla41Sep 1, 2025
Why has the noise increased in the bevel transmission of my KNEGT 404G2?
- P
  Patrick WarrenSep 1, 2025
  Increased noise in the bevel transmission of your KNEGT Tractor can be attributed to several factors. The bearing clearance of the small helical bevel might be too large, requiring adjustment. Abnormal gear engagement should also be adjusted. A differential shaft that is abraded and seized needs replacement. Additionally, abraded planetary gears or washers should be replaced. Finally, abraded or damaged differential bearings should also be replaced.
J
Jennifer BookerSep 2, 2025
Why are the front wheels swaying on my KNEGT 404G2 Tractor?
- E
  Erika JohnsonSep 2, 2025
  Swaying front wheels on your KNEGT Tractor can be caused by several issues. The bearing of the front driven axle may be heavily abraded, requiring replacement. Similarly, a heavily abraded bearing of the steering knuckle should also be replaced. If the clearance of the front and rear supporting seat is too large, it needs adjustment. A seriously deformed front wheel rim should be corrected. Finally, improper front wheel toe-in adjustment should be adjusted.
J
Jason EdwardsSep 3, 2025
Why is it difficult to gear or impossible to gear on my KNEGT 404G2 Tractor?
- K
  Katherine SantanaSep 3, 2025
  If you find it difficult to gear or are unable to gear on your KNEGT Tractor, it could be due to the clutch not separating completely; remedy as per clutch troubles. Another cause could be that the mesh sleeve end face and gear end face are abraded seriously or damaged, requiring replacement or repair.