EasyManua.ls Logo

Kold-Draft GT561LC - User Manual

Default Icon
85 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
- -
Installation, Operation, Technical
Service and Replacement Parts Manual
Ice Cube Makers - GT36x, GT56x, GB56x, GB106x
Stacking Instructions - Multiple GB56x or GB106x
Ice Cube Crushers - T27x
Pre-charged Remote Air-Cooled Condenser - RC214APV
GT36x GT56x GB56x GB106x
KDIndustries, Inc.
1525 East Lake Road
Erie, PA 16511-1088 U.S.A.
(800) 840-9577
FAX: (800) 548-9392
www.kold-draft.com
November 2016
This manual is updated periodically. Visit http://www.kold-draft.com/resources/literature.php for the latest version.

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Kold-Draft GT561LC and is the answer not in the manual?

Summary

KOLD-DRAFT Installation, Operation, Technical Service and Replacement Parts Manual

ICE CUBER SAFETY INFORMATION

Hazard Warning Definitions

Defines Warning, Caution, and Danger symbols for hazard communication.

ICE MAKER IDENTIFICATION

ICE CUBER INSTALLATION

General Installation Warnings

Crucial safety warnings to observe during the installation process.

SPECIFICATIONS

CONTROLLER

Fault Code Overview

Description of fault codes monitored by the electronic control.

Fault Code >10, >20, >30

Troubleshooting for evaporator temp, water plate close, freeze time faults.

Fault Code >40, >50

Troubleshooting for freeze time and harvest cycle faults.

Fault Code >60, >70, >80, >90

Troubleshooting for water fill, temp, arm switch, and rinse mode faults.

SEQUENCE OF OPERATION

ERROR-CODE TROUBLESHOOTING

Fault Code >10 Evaporator Temp

Troubleshooting for evaporator temperature over 120F.

Fault Code >20 Water Plate Close

Troubleshooting for water plate failure to close.

Fault Code >30 Freeze Time

Troubleshooting for freeze time exceeding 60 minutes.

Fault Code >40 Freeze Time

Troubleshooting for freeze time less than 5 minutes.

Fault Code >50 Harvest Cycle

Troubleshooting for harvest cycle exceeding 20 minutes.

Fault Code >60 Water Fill

Troubleshooting for water fill exceeding time limits.

Fault Code >70 Evaporator Temp

Troubleshooting for low evaporator temp during fill.

Fault Code >80 Arm Switches

Troubleshooting for arm switch errors.

Fault Code >90 Rinse Mode

Troubleshooting for machine in full-rinse mode.

WIRING DIAGRAMS

COMPRESSOR TEST PROCEDURE

Ground Fault Test Procedure

Procedure to test for short circuits to ground.

Continuity and Resistance Test

Tests motor windings for continuity and proper resistance.

Potential Relay, Run, and Start Capacitor Tests

Procedures for testing relay and capacitors.

WATER PLATE REPLACEMENT

Step-by-Step Replacement Procedure

Detailed instructions for replacing the water plate assembly.

WATER PLATE ALIGNMENT

Alignment Procedure

Steps to align the water plate with the evaporator for proper cubing.

WATER PLATE UP;DOWN POSITION AND ADJUSTMENT

ACTUATOR MOTOR ELECTRICAL TESTS

PROBE TEST PROCEDURE

TROUBLE SHOOTING

Ice Machine Not Operating

Troubleshooting steps when the ice machine is not running.

Compressor Not Operating

Troubleshooting when the compressor is off but other components run.

Condenser Fan Motor Issues

Troubleshooting for condenser fan motor not operating.

Defrost Performance Issues

Troubleshooting slow defrost or ice attachment problems.

Water Plate Opening Issues

Troubleshooting water plate reopening immediately after closing.

Water Plate Closing Issues

Troubleshooting water plate closing before fill completion.

Water Plate Will Not Close After Defrost

Troubleshooting water plate failure to close after defrost.

Defrost Initiation Failure

Troubleshooting defrost not initiating when water level drops.

Premature Defrost Termination

Troubleshooting defrost ending before ice is out.

Defrost Valve Opens During Fill

Troubleshooting defrost valve opening during water fill.

Ice Remains Attached to Water Plate

Troubleshooting ice sticking to water plate at end of defrost.

Water Valve Closing Issues

Troubleshooting water valve not closing during fill.

Water Valve Opening Issues

Troubleshooting water valve not opening during fill.

PARTS DIAGRAMS

ICE CRUSHER SAFETY INFORMATION

General Safety Precautions

Important safety warnings for crusher operation and maintenance.

ICE CRUSHER INSTALLATION

ICE CRUSHER CLEANING PROCEDURE

WIRING DIAGRAM

Minimum Total Charge Required

Kold-Draft GT561LC Specifications

General IconGeneral
BrandKold-Draft
ModelGT561LC
CategoryIce Maker
LanguageEnglish

Related product manuals