To Next PageTo Next PageWhat to do if Konica Minolta Medical Equipment shows E error?
If your Konica Minolta Medical Equipment shows an 'E error', you should check the description of the error, address the problem, and then press the [Reset/Cancel] button.
Why is my Konica Minolta Medical Equipment not printing?
If your Konica Minolta Medical Equipment is not printing, check the message display window for any error messages. Also, verify that the film size is consistent with the study requirements.
How to shut down Konica Minolta Medical Equipment?
If you're unable to shut down your Konica Minolta Medical Equipment, ensure you press the operation switch until you hear a beep (approximately one second). Alternatively, try holding down the operation switch for 10 seconds.
What to do if Konica Minolta DRYPRO 832 shows error message starting with 'F'?
If your Konica Minolta DRYPRO 832 displays an error message starting with 'F', shut it down and then restart it.
What to do if tray cannot open on Konica Minolta Medical Equipment?
If the tray on your Konica Minolta Medical Equipment won't open, check if the message 'Film Empty' is displayed. Also, verify that the machine is not currently printing and that another user is not logged in for maintenance.
Why Konica Minolta Medical Equipment cannot communicate with Printlink5-IN/console?
If your Konica Minolta Medical Equipment cannot communicate with Printlink5-IN/console, check if 'PC not connected' is displayed. Also, ensure the communication cable is properly connected to the Ethernet port.
What to do if Konica Minolta Medical Equipment diagnostic image is not output?
If the diagnostic image is not output from your Konica Minolta Medical Equipment, check if [E9211] is displayed in the message display window.
What to do if Konica Minolta Medical Equipment shows F error?
If your Konica Minolta Medical Equipment shows an 'F error', press the operation switch until a beep sounds (approximately one second) to shut down the machine. After it has shut down, press and hold the operation switch again until a beep sounds (approximately one second) to restart it.
Why Konica Minolta Medical Equipment shows E error when film size is incorrect?
If your Konica Minolta Medical Equipment displays an 'E error' because the entered image film size/type is incorrect (this often happens when an item remains in the queue and the film size or type is changed on the main unit operation panel), a film size/type input image that differs from the main unit settings was specified. You should check the film size/type settings for the input destination modality and press the [Reset/Cancel] button.
What to do if Konica Minolta Medical Equipment power is not turned on?
If the Konica Minolta Medical Equipment is not turning on, verify that you have pressed the operation switch until you hear a beep (approximately one second). Also, ensure you haven't pressed the operation switch twice. Check if the power supply circuit breaker is turned on. If you previously shut down the equipment by holding the operation switch for 10 seconds, ensure you turned off the power supply circuit breaker and then turned it back on. Finally, confirm that the outlet's power supply is functioning correctly.
Important safety precautions and warnings for users regarding manual reproduction, changes, and manufacturer responsibilities.
Information on registered trademarks like Microsoft Windows and other company product names used in the document.
Details the meaning of various safety symbols used, including those indicating care, prohibition, and compulsory actions.
Defines signal words (DANGER, WARNING, CAUTION) used to indicate hazard levels and associated risks.
Details the locations and types of various warning labels attached to the DRYPRO 832 unit.
Provides comprehensive safety guidelines for handling and repairing the DRYPRO 832, including legal requirements.
Identifies and names the key exterior and interior parts of the DRYPRO 832 unit.
Illustrates the overall structure of the DRYPRO 832, including the film feeding order with and without the Lispl-832 option.
Lists the essential tools, measuring instruments, and jigs required for servicing the DRYPRO 832.
Describes the step-by-step procedure for removing and installing the supply tray.
Provides instructions on how to open and close the front and right covers of the unit.
Details the procedures for removing and installing various exterior covers of the unit.
Explains the procedure for installing a wrist grounding strap to prevent electrostatic discharge damage.
Describes how to manually unlock the tray when the tray shutter cannot be inserted or the supply tray cannot be pulled out.
Details the loading parts within the light shield unit of the supply unit.
Details the loading parts within the pickup unit of the supply unit.
Identifies the loading parts included in the tray unit.
Procedure for replacing the motor that drives the elevating plate.
Procedure for replacing the photo sensor that detects the elevating plate's home position.
Procedure for replacing the solenoid valve that locks or unlocks the supply tray.
Procedure for replacing the photo sensor that detects the presence or absence of the supply tray.
Procedure for replacing the light shield unit assembly used for shading film.
Details the loading parts within the light shield unit of the Lispl-832 (optional).
Details the loading parts within the pickup unit of the Lispl-832 (optional).
Details the loading parts within the supply unit of the Lispl-832 (optional).
Details the loading parts within the elevating transport unit of the Lispl-832 (optional).
Identifies loading parts within the sub scan unit.
Procedure for removing and installing the sub scan unit assembly.
Procedure for replacing the sub scan unit, including the position regulation unit.
Procedure for replacing the photo sensor that detects right cover operation.
Procedure for replacing the photo sensor detecting film transport at the justification unit inlet.
Procedure for replacing the drive motor for film transport in the justification unit.
Procedure for replacing the moderation belt.
Procedure for replacing the transfer belt.
Procedure for replacing the drive motor for film transport in the sub scan unit.
Procedure for replacing the motor that drives the nip in the sub scan unit.
Procedure for replacing the photo sensor detecting film transport at the sub scan unit inlet.
Procedure for replacing the photo sensor detecting the home position of the nip in the sub scan unit.
Procedure for replacing the photo sensor detecting film transport in the sub scan unit.
Procedure for replacing the reference guide that regulates film position during transport.
Displays the placement of the exposure unit, which is an optical exposure component.
Procedure for replacing the main scan unit (exposure unit).
Identifies loading parts on the heat process side of the heat process unit.
Identifies loading parts on the main unit side of the heat process unit.
Displays the placement of the ejection unit, which ejects film.
Procedure for replacing the ejection unit that ejects film.
Identifies the loading parts included in the main unit.
Procedure for replacing the photo sensor detecting front cover operation.
Procedure for replacing the main board that controls the DRYPRO 832.
Procedure for replacing the compact flash memory that retains setting data.
Procedure for replacing the MEC board that controls motors and sensors.
Procedure for replacing the multiple power supply unit that supplies DC voltage.
Procedure for replacing the H-DRV board that controls the heat process unit heater.
Procedure for replacing the noise filter that removes AC voltage noise.
Procedure for replacing the fan unit that cools the control unit.
Identifies loading parts located on the exterior of the main unit.
Procedure for removing and installing the operation panel exterior.
Procedure for replacing the message display LCD board on the operation panel.
Procedure for replacing the status lamp that indicates the operating status.
Procedure for replacing the operation switch board.
Details the schedule and tasks for periodic maintenance of the DRYPRO 832.
Procedure for replacing the pickup roller that transports film from the supply tray.
Procedure for replacing the opposed roller that transports film for exposure and heat processing.
Instructions for cleaning the guide in the heat process unit through which film passes.
Procedure for cleaning the air intake filter located in the control box.
Procedure for cleaning the air intake filter located in the power supply unit.
Procedures for correcting image unevenness, including pitch and density.
Guides for checking and adjusting the image data writing position using the utility tool.
Procedures for checking and fine-tuning the print size based on scan offsets.
Describes the method for starting up the DRYPRO 832 Utility Tool.
Allows confirmation and deletion of print jobs in DRYPRO 832.
Procedure for setting print parameters for each connected diagnostic device.
Allows performing various test prints with specified conditions.
Procedure for setting the film border size.
Displays QC pattern results based on densitometer readings.
Allows setting the logo mark to be output on the film.
Displays film data (total count) by film size type, CH, and film size/CH combination.
Procedure for setting parameters for the film loaded in the supply tray.
Sets the method and timing for performing automatic density calibration.
Performs setup for the operation of the internal system of DRYPRO 832.
Sets the date/time layout for the stamp to be printed on film.
Deletes all jobs in the DRYPRO 832, resetting to factory defaults.
Provides information on how to initialize the periodic inspection schedule.
Checks or changes constants for controlling the heat process unit.
Checks or changes settings via mechanical control.
Checks or changes constants to control hardware.
Sets constants for adjusting image quality.
Displays a history of errors that occurred in DRYPRO 832 and PC.
Covers densitometer calibration and setup procedures.
Resets various DRYPRO 832 data to factory defaults.
Provides an overview of MainteTool usage and basic configuration.
Details the network setup procedure for connecting the service PC to the facility's network.
Step-by-step guide on how to access and start the MainteTool program.
Provides information and procedures for upgrading DRYPRO 832 and Printlink5-IN software.
Instructions for saving the contents set in DRYPRO 832 and Printlink5-IN as a backup file.
Procedure to restore setup data from a saved backup file.
Procedure for collecting and loading DRYPRO 832 and Printlink5-IN logs.
Procedure for collecting job data processed by Printlink5-IN.
Conducts motor and sensor operation tests via MEC mechanical control.
Measures laser intensity of the main scan unit and performs print I/O tests.
Provides solutions for common problems encountered with the DRYPRO 832 main unit.
Explains error messages and provides solutions for errors displayed on the operating panel and MainteTool.
Details the procedures for replacing various units of the DRYPRO 832 when a malfunction occurs.
Illustrates the placement of electronic components in various units like Supply, Sub Scan, and Main units.
Illustrates the placement of mechanical components in various units like Supply, Lispl-832, and Sub Scan units.
Provides diagrams of key circuit boards including Main Board, LCD Unit, and MEC Board.
Details specifications for printing management information on film.
Presents the overall block diagram of the DRYPRO 832 system.
Provides detailed wiring diagrams for the system components.
Illustrates the timing chart for printing operations in standard 1-channel mode.
Illustrates the timing chart for printing operations in standard 2-channel mode.
Important safety precautions and warnings for users regarding manual reproduction, changes, and manufacturer responsibilities.
Information on registered trademarks like Microsoft Windows and other company product names used in the document.
Details the meaning of various safety symbols used, including those indicating care, prohibition, and compulsory actions.
Defines signal words (DANGER, WARNING, CAUTION) used to indicate hazard levels and associated risks.
Details the locations and types of various warning labels attached to the DRYPRO 832 unit.
Provides comprehensive safety guidelines for handling and repairing the DRYPRO 832, including legal requirements.
Identifies and names the key exterior and interior parts of the DRYPRO 832 unit.
Illustrates the overall structure of the DRYPRO 832, including the film feeding order with and without the Lispl-832 option.
Lists the essential tools, measuring instruments, and jigs required for servicing the DRYPRO 832.
Describes the step-by-step procedure for removing and installing the supply tray.
Provides instructions on how to open and close the front and right covers of the unit.
Details the procedures for removing and installing various exterior covers of the unit.
Explains the procedure for installing a wrist grounding strap to prevent electrostatic discharge damage.
Describes how to manually unlock the tray when the tray shutter cannot be inserted or the supply tray cannot be pulled out.
Details the loading parts within the light shield unit of the supply unit.
Details the loading parts within the pickup unit of the supply unit.
Identifies the loading parts included in the tray unit.
Procedure for replacing the motor that drives the elevating plate.
Procedure for replacing the photo sensor that detects the elevating plate's home position.
Procedure for replacing the solenoid valve that locks or unlocks the supply tray.
Procedure for replacing the photo sensor that detects the presence or absence of the supply tray.
Procedure for replacing the light shield unit assembly used for shading film.
Details the loading parts within the light shield unit of the Lispl-832 (optional).
Details the loading parts within the pickup unit of the Lispl-832 (optional).
Details the loading parts within the supply unit of the Lispl-832 (optional).
Details the loading parts within the elevating transport unit of the Lispl-832 (optional).
Identifies loading parts within the sub scan unit.
Procedure for removing and installing the sub scan unit assembly.
Procedure for replacing the sub scan unit, including the position regulation unit.
Procedure for replacing the photo sensor that detects right cover operation.
Procedure for replacing the photo sensor detecting film transport at the justification unit inlet.
Procedure for replacing the drive motor for film transport in the justification unit.
Procedure for replacing the moderation belt.
Procedure for replacing the transfer belt.
Procedure for replacing the drive motor for film transport in the sub scan unit.
Procedure for replacing the motor that drives the nip in the sub scan unit.
Procedure for replacing the photo sensor detecting film transport at the sub scan unit inlet.
Procedure for replacing the photo sensor detecting the home position of the nip in the sub scan unit.
Procedure for replacing the photo sensor detecting film transport in the sub scan unit.
Procedure for replacing the reference guide that regulates film position during transport.
Displays the placement of the exposure unit, which is an optical exposure component.
Procedure for replacing the main scan unit (exposure unit).
Identifies loading parts on the heat process side of the heat process unit.
Identifies loading parts on the main unit side of the heat process unit.
Displays the placement of the ejection unit, which ejects film.
Procedure for replacing the ejection unit that ejects film.
Identifies the loading parts included in the main unit.
Procedure for replacing the photo sensor detecting front cover operation.
Procedure for replacing the main board that controls the DRYPRO 832.
Procedure for replacing the compact flash memory that retains setting data.
Procedure for replacing the MEC board that controls motors and sensors.
Procedure for replacing the multiple power supply unit that supplies DC voltage.
Procedure for replacing the H-DRV board that controls the heat process unit heater.
Procedure for replacing the noise filter that removes AC voltage noise.
Procedure for replacing the fan unit that cools the control unit.
Identifies loading parts located on the exterior of the main unit.
Procedure for removing and installing the operation panel exterior.
Procedure for replacing the message display LCD board on the operation panel.
Procedure for replacing the status lamp that indicates the operating status.
Procedure for replacing the operation switch board.
Details the schedule and tasks for periodic maintenance of the DRYPRO 832.
Procedure for replacing the pickup roller that transports film from the supply tray.
Procedure for replacing the opposed roller that transports film for exposure and heat processing.
Instructions for cleaning the guide in the heat process unit through which film passes.
Procedure for cleaning the air intake filter located in the control box.
Procedure for cleaning the air intake filter located in the power supply unit.
Procedures for correcting image unevenness, including pitch and density.
Guides for checking and adjusting the image data writing position using the utility tool.
Procedures for checking and fine-tuning the print size based on scan offsets.
Describes the method for starting up the DRYPRO 832 Utility Tool.
Allows confirmation and deletion of print jobs in DRYPRO 832.
Procedure for setting print parameters for each connected diagnostic device.
Allows performing various test prints with specified conditions.
Procedure for setting the film border size.
Displays QC pattern results based on densitometer readings.
Allows setting the logo mark to be output on the film.
Displays film data (total count) by film size type, CH, and film size/CH combination.
Procedure for setting parameters for the film loaded in the supply tray.
Sets the method and timing for performing automatic density calibration.
Performs setup for the operation of the internal system of DRYPRO 832.
Sets the date/time layout for the stamp to be printed on film.
Deletes all jobs in the DRYPRO 832, resetting to factory defaults.
Provides information on how to initialize the periodic inspection schedule.
Checks or changes constants for controlling the heat process unit.
Checks or changes settings via mechanical control.
Checks or changes constants to control hardware.
Sets constants for adjusting image quality.
Displays a history of errors that occurred in DRYPRO 832 and PC.
Covers densitometer calibration and setup procedures.
Resets various DRYPRO 832 data to factory defaults.
Provides an overview of MainteTool usage and basic configuration.
Details the network setup procedure for connecting the service PC to the facility's network.
Step-by-step guide on how to access and start the MainteTool program.
Provides information and procedures for upgrading DRYPRO 832 and Printlink5-IN software.
Instructions for saving the contents set in DRYPRO 832 and Printlink5-IN as a backup file.
Procedure to restore setup data from a saved backup file.
Procedure for collecting and loading DRYPRO 832 and Printlink5-IN logs.
Procedure for collecting job data processed by Printlink5-IN.
Conducts motor and sensor operation tests via MEC mechanical control.
Measures laser intensity of the main scan unit and performs print I/O tests.
Provides solutions for common problems encountered with the DRYPRO 832 main unit.
Explains error messages and provides solutions for errors displayed on the operating panel and MainteTool.
Details the procedures for replacing various units of the DRYPRO 832 when a malfunction occurs.
Illustrates the placement of electronic components in various units like Supply, Sub Scan, and Main units.
Illustrates the placement of mechanical components in various units like Supply, Lispl-832, and Sub Scan units.
Provides diagrams of key circuit boards including Main Board, LCD Unit, and MEC Board.
Details specifications for printing management information on film.
Presents the overall block diagram of the DRYPRO 832 system.
Provides detailed wiring diagrams for the system components.
Illustrates the timing chart for printing operations in standard 1-channel mode.
Illustrates the timing chart for printing operations in standard 2-channel mode.
General| Brand | Konica Minolta |
|---|---|
| Model | Drypro 832 |
| Category | All in One Printer |
| Language | English |
