Konsberg cNODE MiniS - Turning on the cNODE MiniS

To Next Page

To Previous Page

397152/D

Thetransponderisthenreadyforuse.

TurningonthecNODEMiniS

Thetransponderisdesignedforoperationinwateronly.Thetranspondermaybe

operatedinairfortestpurposesoverashortperiodoftime.

Prerequisites

Thetranspondermustbechargedbeforeuse.

Procedure

1GreasetheconnectorwithMolykote44Mediumorequivalentgrease.

2Connecttheon/offplugtotheendcapconnector.

3Tightenthelockingsleevetotheendcapconnector.

Result

Abuzzcanbeheardwithin25secondsasaconrmationthatthetransponderisactivated.

Furtherrequirements

ItisrecommendedtotestthetransponderwiththeTestandCongurationunit(TTC)to

makesurethetransponderisworkingproperlybeforeoperation.

Gettingstarted

Main Page

Table of Contents5
About this Manual9
Kongsberg Cnode Minis10
System Description11
Naming Description11
System Units12
- Transponders12
- Battery Charger12
- Remote Transducers13
- TTC 30 (Transponder Test and Configuration Unit)13
General Supply Conditions13
- Receipt, Unpacking and Storage13
- Equipment Responsibility14
Support Information14
General Acoustic Considerations15
Getting Started17
Charging the Battery (On-Deck)18
Turning on the Cnode Minis19
Connecting the Transponder to External Power and Responder Signals20
Changing between Responder and Transponder Mode21
Turning on the TTC21
Acoustic Test21
Configuring the Transponder22
Pre-Deployment Checks23
Deployment23
Recovering the Transponder24
Cymbal Protocol24
Operating Procedures25
Maintenance26
Safety Features27
Charging the Battery (On-Deck)27
Greasing the Subconn Connectors28
Battery Charger Status and Troubleshooting29
Spare Parts30
Minis 34-40V Spare Part31
Minis 37-40V Ti Spare Part31
Minis 34-180 Spare Part31
Minis 34-180 PS Spare Part31
Minis 31-180 PS Spare Part31
Minis 34-40V PS Spare Part32
Minis 31-40V PS Spare Part32
Minis 34-S Spare Part32
TDR180 Spare Part32
TDR40V Spare Part32
TDR30H Spare Part32
Transducer Cable Spare Part33
Battery Charger Spare Part33
ON/OFF Plug Spare Part33
Pigtail Cable Spare Part33
TTC 30 (Transponder Test and Configuration Unit) Spare Part33
Test and Configuration Cable (TTC to Minis) Spare Part34
Test and Configuration Cable (PC to Minis) Spare Part34
Drawing File35
Common for All 180° Transducers Outline Dimensions36
Common for All 40° Transducers Outline Dimensions37
Minis 34-S Outline Dimensions38
External Signal Connector Pinout39
TDR180 Outline Dimensions40
TDR40V Outline Dimensions41
TDR30H Outline Dimensions42
Technical Specifications43
Performance Specifications44
Weight and Outline Dimensions48
Power Requirements50
Environmental Requirements50
Battery Safety51
SECTION 1: Identification52
SECTION 2: Hazards Identification52
SECTION 3: Composition53
SECTION 4: First Aid Measures53
SECTION 5: Firefighting Measures54
SECTION 6: Accidental Release Measures54
SECTION 7: Handling and Storage55
SECTION 8: Exposure Control and Personal Protection55
SECTION 12: Ecological Information56
SECTION 9: Physical and Chemical Properties56
SECTION 10: Stability and Reactivity56
SECTION 11: Toxicological Information56
SECTION 13: Disposal Considerations57
SECTION 14: Transport Information57
SECTION 15: Regulatory Information58
SECTION 16: Other Information58

Konsberg cNODE MiniS - Turning on the cNODE MiniS

Table of Contents