Korg Krome

Connecting the keyboard and turning the power on
En-8
Turning the power off
Whenyou’vefinishedusingtheKROME,turnoffthe
powerbypressingthepowerswitchthat’slocatedon
therearpaneloftheKROME.
Whenyouturnoffthepower,anyprogram,
combination,orglobalsettingsyoumayhave
editedwillreturntoitsoriginalstate.Ifyouwant
tokeeptheresultsofyourediting,yo
umustsave
(write)theeditedsettings.
Inthesameway,thesongdatawillalsobelost
whenyouturnoffthepower.Ifyouwanttouse
thesongdataagainlater,youmustsaveitbefore
youturnoffthepower,andthenloaditagain
whende
sired.(See“S
avingyouredits”on
page 19.)
IftheKROME’sautopower‐offfunctionis
enabled,thepowerwillautomaticallyturnoff
afteracertainlengthoftimehaselapsedwithout
anyuserinput.Thisautomaticpower‐offwillalso
causeallunsaveddatatobelost.
Ifthepoweristurnedoffwhiledataisbeing
writtentotheinternalmemo
ry,thedatainthe
internalmemorymaybedamaged.Neverturnoff
thepowerwhileanyprocessisbeingexecuted.
Whileprocessingisoccurring,thefollowing
messagewillappear:
“Nowwritingintointernalmemory”
The auto power-off function
TheKROMEhasanautopower‐offfunctionthat
automaticallyturnsoffthepowerwhenthekeyboard
orfrontpanelbuttonshavenotbeenused(*)fora
certainlengthoftime.
*TheVOLUMEknobisnotincluded.
Note:Withthefactorysettings,thepowerwillturnoff
whentherehasbeennouserinputforapproximately
fourhours.
Whenthepowerturnsoff,anysetting
syouhad
beeneditingwillbelost.Ifyouwanttokeepyour
editedsettings,youmustsavethembeforethe
powerturnsoff.
Changing the auto power-off setting
Changing the settings in the start-up dialog box
Iftheautopower‐offfunctionisenabledsothatthe
powerwillturnoffautomatically,thecurrently
specifiedautopower‐offtimeisdisplayedimmediately
afterthesystemstartsup.
1. Whilethismessageisshown,presstheChange
Settingbuttoninthedialogbox.
Thefollowingdialogboxwillappear.
2. Pressthepopupbuttonandselectthedesiredtime
foraut
opower‐offtooccur.Ifyoudon’twantthe
powertoturnoffautomatically,chooseDisabled.
Note:Ifthisdialogboxdoesnotappearimmediately
afterstart‐up,theautopower‐offfunctionissetto
Disabled;thepowerwillnotturnoffautomatically.
Note:Youcanalsochangetheautopower‐offsetting
duringoperation(seepage 16oftheOperationGuide).
Auto power-off warning message
Whenthespecifiedtimehaselapsed,amessagewill
warnyouthattheautopower‐offfunctionisaboutto
turnoffthepower.
IfyouwanttocontinueusingtheKROME,pressthe
keyboard,abutton,orthedisplay.Autopower‐offwill
bereset,andthesamemessagewillappearwhenthe
spec
ifiedtimehasagainelapsedwithoutanyuser
inpu
t.