Appendices
307
Selected file/path is not correct
Slice point over limit Can’t divide
Source file is not 44100 Hz or 48000 Hz Can’t convert
Source is empty
Source sample is empty
S/P DIF Clock Error !
T
There is no readable data
This file is already loaded
Track is full
U
Unable to create directory
Unable to save file
USB Hub Power Exceeded!
USB Hub power exceeded Please disconnect USB device
W
WAVE file size over limit
Meaning: When loading a divided .PCG file, you attempted
to load a .PCG file of the same name that was not
divided or had differing contents.
Action: Load the correct .PCG file.
Meaning: When loading a KSF file that was split across mul-
tiple media, the order in which you attempted to
load the files was incorrect.
Action: Load the KSF file in the correct order. To view the
file number order in which the KSF files were
saved, you can check the Media mode “Transla-
tion” page menu command. (The sample name
and number of the first KSF file will be displayed.)
Meaning: When using the Sampling mode “Time Slice” or
“Time Stretch” commands, the Slice setting would
divide the sample into more samples than the
maximum possible number (1000), and thus
“Divide” cannot be executed.
Action: Use “Link” to connect any “Index” that you do
not require, and then execute “Divide.”
Meaning: When executing the Media mode utility page
menu command “Rate Convert” or the Edit
WAVE page menu command “Rate Convert,” you
selected a WAVE file whose sampling rate was
other than 44.1 kHz or 48 kHz.
Action: WAVE files other than 44.1 kHz or 48 kHz cannot
be converted.
Meaning: No data exists in the track or pattern that you
specified as the source.
Action: Specify a track or pattern that contains musical
data.
Meaning: When executing Insert, Mix, or Paste, the source
sample is empty.
Action: Execute the Copy operation before executing
Insert, Mix, or Paste.
Meaning: When “System Clock” was set to S/P DIF, the
clock could not be detected correctly.
Action: Check whether the digital output from the exter-
nal device is being output correctly. Sampling fre-
quencies of 48 kHz can be input to the TRITON
Extreme.
Also check whether there is a problem with the
optical cable.
Meaning: Either the file size is 0 or the file does not contain
data that can be accessed by the load or open
operation. Alternatively, the data is damaged etc.,
and cannot be loaded or accessed.
Meaning: When loading a divided .PCG file, you attempted
to load a file that had already been loaded.
Action: Load the .PCG files that have not yet been loaded.
Meaning: In the Media mode Make Audio CD page, you
attempted to insert a track that would make the
total exceed 99 tracks.
Action: Cut unneeded tracks, and then execute the Insert
operation once again.
Meaning: You attempted to create a directory that would
exceed the maximum pathname length (76 charac-
ters for the full pathname).
Meaning: When executing the Media mode Utility com-
mand “Copy,” the copy destination path length
exceeded 76 characters.
Meaning: When saving a file in each mode, the save destina-
tion path exceeded 76 characters.
Meaning: When you executed the Media mode Utility page
menu command “Copy,” the file management
data exceeded the size of the management area.
Meaning: The power consumption of the USB devices
exceeds the amount that the connected hub can
supply. In this state, the USB devices will not be
detected correctly.
Action: If your USB hub or device is able to operate in a
self-powered mode, use it in self-powered mode.
If you are using more than one USB hub, you may
be able to solve the problem by connecting to a
different USB hub.
After reconnecting, you’ll need to execute “Scan
USB Device.”
Meaning: When using Media mode Edit WAVE to edit, you
exceeded the maximum allowable length of
230,400,000 samples (80 minutes at a sampling
rate of 48 kHz) for a WAVE file.
Action: You cannot use Edit WAVE to edit a WAVE file
that exceeds 230,400,000 samples (80 minutes at a
sampling rate of 48 kHz).
To Next Page
Loading...
