Korg TRITON Extreme - Table of Contents

iv
1. Program mode. . . . . . . . . . . . .1
Program P0: Play ......................................... 1
Select and play programs.
0–1: Perf. Edit
Select and play programs; use the
Performance Editor for simple editing
... 1
0–2: Arpeggio
Arpeggio pattern selection and settings
.4
0–3: Sampling
Perform sampling; make settings for
audio inputs etc.
......................................... 4
Program P1: Edit–Basic.................................. 9
Make basic oscillator settings and scale settings etc.
1–1: Program Basic
Oscillator settings for Single/Double/
Drums, Poly/Mono, scale etc.
.................. 9
1–2: OSC Basic
Specify the multisample for oscillators 1
and 2
.......................................................... 11
1–3: Velo. Zone
Velocity zone settings
............................. 13
1–4: Controller
[SW1] and [SW2] key functions;
REALTIME CONTROLS [1]–[4] knob B-
mode functions
........................................ 14
Program P2: Edit–Pitch .................................14
Make pitch-related settings for oscillators 1 and 2.
2–1: OSC1 P.Mod
Specify oscillator 1 pitch modulation via
key position or controllers
...................... 14
2–2: OSC2 P.Mod
Specify oscillator 2 pitch modulation via
key position or controllers
...................... 16
2–3: Pitch EG
Pitch EG settings
...................................... 16
Program P3: Edit–Filter .................................18
Make filter settings for oscillators 1 and 2.
3–1: Filter1
Filter 1 (for oscillator 1) type, cutoff
frequency, and resonance settings
........ 18
3–2: Filter1 Mod.
Keyboard tracking and controller settings
to modulate the filter 1 cutoff frequency
.................................................................... 19
3–3: Filter1 LFO Mod.
Filter 1 LFO settings to modulate the filter
1 cutoff frequency
.................................... 20
3–4: Filter1 EG
Filter 1 EG settings
................................... 21
3–5: Filter2
Filter 2 (for oscillator 2) type, cutoff
frequency, and resonance settings
........ 22
3–6: Filter2 Mod.
Keyboard tracking and controller settings
to modulate the filter 2 cutoff frequency
....................................................................22
3–7: Filter2 LFO Mod.
Filter 2 LFO settings to modulate the filter
2 cutoff frequency
....................................22
3–8: Filter2 EG
Filter 2 EG settings
...................................22
Program P4: Edit–Amp.................................. 23
Make amp settings for oscillators 1 and 2.
4–1: Amp1 Level/Pan
Oscillator 1 volume and pan settings
....23
4–2: Amp1 Mod.
Keyboard tracking and controller settings
to modulate amp 1
...................................23
4–3: Amp1 EG
Amp 1 EG settings
...................................24
4–4: Amp2 Level/Pan
Oscillator 2 volume and pan settings
....26
4–5: Amp2 Mod.
Keyboard tracking and controller settings
to modulate amp 2
...................................26
4–6: Amp2 EG
Amp 2 EG settings
...................................26
Program P5: Edit–Common LFO....................... 26
Make settings for the general purpose LFOs used to cycli-
cally modulate the pitch, filter, and amp of oscillators 1
and 2.
5–1: OSC1 LFO1
OSC1 LFO1 (for oscillator 1) settings
...26
5–2: OSC1 LFO2
OSC1 LFO2 (for oscillator 1) settings
...27
5–3: OSC2 LFO1
OSC1 LFO1 (for oscillator 2) settings
...27
5–4: OSC2 LFO2
OSC1 LFO2 (for oscillator 2) settings
...27
Program P7: Edit-Arpeggiator ......................... 28
Make settings for the arpeggiator.
7–1: Arpeg. Setup
Select an arpeggio pattern and make
settings
.......................................................28
7–2: Scan Zone
Specify the note and velocity ranges that
will operate the arpeggiator
...................29
Program P8: Edit–Insert Effect......................... 30
Specify the oscillator output bus, and make insert effect
settings.
8–1: Routing
Specify the oscillator output bus and set
the send levels to the master effects
......30
8–2: Insert FX
Select insert effects and turn them on/off,
and make chain settings
..........................31
8–3: IFX 1
Parameter settings for IFX1
....................32
8–4: IFX 2
Parameter settings for IFX2
....................32
8–5: IFX 3
Parameter settings for IFX3
....................32
8–6: IFX 4
Parameter settings for IFX4
....................32
8–7: IFX 5
Parameter settings for IFX5
....................32
Program P9: Edit–Master Effect ....................... 32
Make settings for the master effects, the master EQ, and
Valve Force.
9–1: Master FX
Select master effects and turn them on/
off, and make chain settings
...................32
9–2: MFX 1
Parameter settings for MFX1
..................34
9–3: MFX 2
Parameter settings for MFX2
..................34
9–4: Master EQ
Parameter settings for master EQ
..........34
9–5: VALVE FORCE
Settings for Valve Force
..........................34
Table of Contents