41
Combination
P0
P1 P2 P3 P4 P7 P8 P9
0–3a: Arpeggiator Run A, B, Timbre assign
Arpeggiator Run A, B
When the ARPEGGIATOR [ON/OFF] key is on, the arpeg-
giator(s) you checked here will run if they are assigned to a
timbre by “Arpeggiator Assign” (7–1b).
When the arpeggiator is on, these check boxes let you turn A
and B on/off.
This parameter can also be set from P7: Edit-Arp. Setup
page “Arpeggiator Run A, B.”
Timbre assign
This indicates the arpeggiator A and B assignment status for
each timbre 1–8. These settings are made in “Arpeggiator
Assign” (7–1b).
0–3(4)b: Arpeggiator A (B)
Pat (Pattern) [P000...P004, U000(A/B)...U506(User)]
Octave [1, 2, 3, 4]
Reso (Resolution) [ , , , , , ]
Sort [Off, On]
Latch [Off, On]
Key Sync. [Off, On]
Keyboard [Off, On]
Set the various parameters of the combination arpeggiator
(☞“Program P7: Edit-arpeggiator”).
These parameters can also be set from 7–2(3): Arpegg. A(B).
0–5: Sampling
Here you can adjust the settings for the analog/digital audio
signal input (AUDIO INPUT, S/P DIF), and the sampling-
related settings for Combination mode.
As in Program mode, sampling in Combination mode
allows you to sample an incoming audio signal or to resam-
ple a TRITON Extreme performance. (☞Program P0: 0–3)
The TRITON Extreme can also be used as a 4-in 6-out effect
processor.
0–5a: Input (COMBI, PROG, SEQ, S.PLAY, MEDIA)
Input [Analog, S/P DIF]
Input1:
Input2:
Level [0...127]
Pan [L000...C064...R127]
BUS(IFX/Indiv.) Select
[L/R, IFX1…5, 1, 2, 3(Tube), 4(Tube), 1/2, 3/4(Tube), Off]
Send1(MFX1), Send2(MFX2) [000...127]
Specify the input source analog/digital audio device, and
set the input level, pan, bus, and master effect sends.
Input settings are valid in Combination, Program,
Sequencer, Song Play, and Media modes. (☞Global P0:
0–3a)
0–5b: Sampling Setup
Source BUS [L/R, Indiv.1/2]
Trigger [Sampling START SW, Note On]
Metronome Precount [Off, 4, 8, 3, 6]
Save to [RAM, MEDIA]
Mode (Sample Mode) [L-Mono, R-Mono, Stereo]
Sample Time [min sec]
Make settings for sampling in Combination mode. (☞Pro-
gram P0: 0–3)
Sampling Setup settings apply to the entire Combination
mode; not to an individual combination.
0–5c: Recording Level [dB]
ADC OVERLOAD !!
Recording Level [–inf, –72.0... 0.0...+18.0dB]
Adjusts the signal level at the final stage of sampling in
Combination mode. (☞Sampling P0: 0–1d)
This setting defaults to –12 dB when you turn on the power.
At a setting of –12 dB, CLIP!! will not appear even if you
play the Combination at its maximum level.
(☞Program P0: 0–3c “Recording Level”)
▼ 0–5: Page Menu Command
☞ The illustration shown here is for when you’ve selected
“Save to” RAM. If you’ve selected MEDIA, this menu will
show “Select Directory” instead of “Select Bank & Smpl
No.” For details on “Select Directory,” refer to Program
P0: 0–3D.
0–5
0–5a
0–5b
0–5c
0–1A
0–1B
Program
0–3A
Program
0–3B
Program
0–3D
0–5A
0–1C
To Next Page
Loading...
