82
1 Use “Track Select” to select the MIDI track (Track 01–16)
that you want to insert data into.
2 Select “Insert Measure” to access the dialog box.
3 In “At Measure,” specify the measure location at which
the data will be inserted. (The measure you specified in
Track Edit page “From Measure” will be set as a default.)
4 In “Length,” specify the number of measures that will be
inserted.
5 In “Meter,” specify the time signature of the measures
that will be inserted.
If you want the inserted measures to match the existing
time signature, specify **/**. With any setting other than
**/**, the time signature of the inserted measures will
change, and the specified time signature will apply to all
tracks for those measures.
6 If you wish to insert measures into all tracks including
the master track, check “All Tracks.” The musical data
following the inserted measures will playback in the
same way it did before the measures were inserted.
If “All Tracks” is unchecked, the measures will be
inserted only into the specified track. At this time, the
musical data following the inserted location will be
moved toward the end of the sequence by the number of
measures that were inserted. However, the time signa-
ture and tempo recorded in the master track and will not
change.
7 To execute the Insert Measure command, press the OK
button. To cancel, press the Cancel button.
5–1I: Repeat Measure
This command repeatedly inserts the specified measures for
the specified number of times. When you execute the Repeat
Measure command, the measures will be inserted following
the measure specified by “To End of Measure,” and musical
data following the inserted data will be moved backward. It
is convenient to use this command when you have a song
that you playback with “Track Play Loop” (0–5a/6a) turned
on, and wish to expand it into musical data.
1 Use “Track Select” to select the MIDI track (Track 01–16)
that you want to insert data into.
2 Select “Repeat Measure” to access the dialog box.
3 In “From Measure” and “To End of Measure,” specify
the range of measures that will be repeated. (By default,
“From Measure” and “To End of Measure” will be set to
the range you specified in the Track Edit page.)
4 In “Times,” specify the number of repetitions. For exam-
ple if you set “From Measure” to 001, “To End of Mea-
sure” to 004, and “Times” to 2, the musical data of
measures 1–4 will be inserted into measures 5–8. The
result will be that measures 1–4 will be played twice.
5 Specify the track(s) on which you want to execute the
command.
If you execute with “All Tracks” unchecked, the perfor-
mance data will be inserted into the track you specified
in “Track Select.” Be aware that in this case, the perfor-
mance data following the insert position will move back-
ward (i.e., toward the end of the song) by the number of
inserted measures, but the time signature and tempo will
not move.
If you execute with “All Tracks” checked, the perfor-
mance data will be inserted into all tracks, including the
master track. The performance data following the
inserted measures will play back in the same way as it
did before.
6 To execute the Repeat Measure command, press the OK
button. To cancel, press the Cancel button.
5–1J: Copy Measure
This command copies the measures of musical data speci-
fied as the “From” source to the begining of the measure
specified as the “To” location.
When you execute the Copy Measure command, the exist-
ing track data at the copy destination will be rewritten.
1 Select the copy source song.
2 Select “Copy Measure” to access the dialog box.
3 In From: “Track” select the copy source track. (By
default, this will be the track you selected in “Track
Select.”)
If you check “All Tracks,” the musical data of all tracks
including the master track will be copied.
4 In “From Measure” and “To End of Measure,” specify
the range of copy source measures. (By default, “From
Measure” and “To End of Measure” will be the range that
you specified in the Track Edit page.)
5 Use To: “Song” to specify the copy-destination song,
“Track” (if “All Tracks” is unchecked) to specify the
copy-destination track, and “Measure” to specify the
starting measure at which the copied data will be
inserted.
Time signature = **/**
Track 2
5 (2/4)4 (5/4)1 (4/4) 2 (7/8) 3 (7/8)
1 (4/4) 2 (4/4) 4 (5/4) 5 (2/4)3 (3/4)
1 (4/4) 2 (4/4) 4 (5/4) 5 (2/4)3 (3/4)
1 (4/4) 2 (7/8) 4 (5/4) 5 (2/4)3 (7/8)
Track 2
5 (2/4)4 (5/4)
Track 2
1 (4/4) 2 (4/4)
1 (4/4) 2 (4/4) 4 (5/4) 5 (2/4)3 (3/4)
3 (3/4)
1 (4/4) 2 (4/4) 4 (5/4) 5 (2/4)3 (3/4)
1 (4/4) 2 (4/4) 4 (5/4) 5 (2/4)3 (3/4)
Track 1
Track 1
Track 1
Track 2
Track 1
Time signature = 7/8
Before Insert
After Insert
Before Insert
After Insert
Insert two measures
Insert two measures
Measures 4 and 5 will use the previously specified
time signature.
Measures 2 and 3 will be 7/8, and measures 4 and 5
will be the previously specified time signature.
1 2
3 4
5 6
1 2
3 4
1 2
3 4
5 6
Track 1
Track 1
Before
Repeat
Measure
After
Repeat
Measure
If you execute the Repeat Measure operation on measures 1–4 with “Time” = 2,
measures 1–4 will be inserted into measures 5–8.
To Next Page
Loading...
