Krone Comprima F 125-1 - Preparing the Machine for Transportation; Raising the Machine

Driving and Transport
105
Pos: 41.39.1 /Überschr iften/Überschr iften 2/U-Z/VVorberei tung der Maschine für die Beförderung @ 395\mod_144 6625169194_78.doc x @ 2815316 @ 2 @ 1
8.3 Preparing the machine for transportation
Pos: 41.39.2 /BA/Si cherheit/2. Vor angestellte WarnhinweiseAc htung - Maschinensc haden durch nicht gesi cherte bewegliche Maschi nenteile beim Transpor t @ 395\mod_144661898 8846_78.docx @ 2815285 @ @ 1
CAUTION!
Risk of machine damage due to unsecured moving machine parts
When transporting the machine on transportation vehicles (e.g. trucks or trains), excessive
bursts of air may damage it.
• Carry out the following measures to secure moving machine parts.
Pos: 41.39.3 /Überschr iften/Überschr iften 3/K-O/M/Maschine an heben @ 404\mod_14490 46995819_78.docx @ 287 0115 @ 3 @ 1
8.3.1 Raising the Machine
Pos: 41.39.4 /BA/Si cherheit/7. Gefahr enhinweise alt/W arnung - Anheben @ 168\mod_136843 3456450_78.docx @ 1454049 @ @ 1
WARNING!
Danger from falling loads!
• Never step or stay under suspended loads!
• Maintain an adequate safety distance from suspended loads.
• Before transportation, compare load capacity of slings and cranes and choose
transportation equipment with a sufficient degree of safety and lifting capacity.
• Prevent strong impacts and make sure that the machine does not become wedged!
Pos: 41.39.5 /BA/W artung/Rundballenpress e/Anheben der Maschi ne_Einleitung_Ansc hlagpunkte_Compri ma F/V_+X-treme_Forti ma @ 472\mod_1472126278942_ 78.docx @ 3193213 @ @ 1
The baler is equipped with three suspension points:
• A suspension point is located in the front area of the drawbar.
• Two suspension points can be found rear on the yoke (right and left upper machine side).
Pos: 41.39.6 /Layout Module /----------------Leerzeile-------------------- @ 240\mod_1395147357027_0.docx @ 1890988 @ @ 1
Pos: 41.39.7 /BA/S icherheit/8. Vor aussetzungen/Handlungsa nweisung für alle Maschi nen/Handlungsan weisung: Maschine sti llsetzen und sic hern @ 274\mod_140436525384 9_78.docx @ 2065151 @ @ 1
• Shut down and safeguard the machine, see chapter Safety -> Safety routines, "Shutting
down and safeguarding the machine".
Pos: 41.39.8 /BA/W artung/Rundballenpress e/Anheben der Maschi ne_Text_ALLE Compri ma_Fortima @ 472\mod_14720 44219370_78.doc x @ 3190614 @ @ 1
• Use a lifting beam with a minimum load-bearing capacity (depending on the permitted total
weight of the machine), see chapter Description of machine, "Identification".
• Close the tailgate.
• Move the support jack to the transport position.
• Lift out the pick-up.
• Ensure that all safety devices are locked.
• Attach the chains of the lifting beam to the stop points on the machine.
• Make sure that the chain hooks are correctly placed on the stop points.
Pos: 41.39.9 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.d ocx @ 4165 @ @ 1