KStar KSG-15K - User Manual

Questions and Answers

M
Mike CampbellSep 3, 2025
What to do if KStar KSG-15K displays 'Inverter DC Current high' (F11)?
- A
  Angelica BallSep 3, 2025
  If your KStar Inverter displays 'Inverter DC Current high' (F11), here’s what you should do: 1. Disconnect the PV input and restart the inverter after a few minutes to see if the fault clears. 2. If the fault persists, contact your local distributor.
D
Debra MitchellSep 18, 2025
What to do if KStar KSG-15K Inverter displays 'DSP communication Lost' (F32)?
- M
  mary67Sep 18, 2025
  If your KStar Inverter displays 'DSP communication Lost' (F32), here’s what you should do: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
L
Linda AtkinsonSep 16, 2025
What to do if KStar KSG-15K Inverter displays 'DSP Operation Fault' (F24)?
- M
  Ms. Christina ColonSep 16, 2025
  If your KStar Inverter displays 'DSP Operation Fault' (F24), here’s what you should do: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
I
imedinaSep 14, 2025
What to do if KStar KSG-15K Inverter displays 'Consistency Frequency Fault' (F23)?
- S
  samantha26Sep 14, 2025
  If your KStar Inverter displays 'Consistency Frequency Fault' (F23), here’s what you should do: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
T
Tamara JohnsonSep 12, 2025
What to do if KStar Inverter displays 'Consistency Voltage Fault' (F22)?
- D
  Dawn OchoaSep 12, 2025
  If your KStar Inverter displays 'Consistency Voltage Fault' (F22), here’s what you should do: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
J
jeffreycarterSep 12, 2025
What to do if KStar KSG-15K displays 'Leakage Current Self-Checking Failure' (F21)?
- D
  Donald GoldenSep 12, 2025
  If your KStar Inverter displays 'Leakage Current Self-Checking Failure' (F21), here’s what you should do: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
A
Ashley HoffmanSep 9, 2025
What to do if KStar KSG-15K Inverter displays 'Leakage Current High' (F20)?
- S
  Sydney CarrSep 9, 2025
  If your KStar Inverter displays 'Leakage Current High' (F20), here’s what you should do: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
D
dmendezSep 7, 2025
How to troubleshoot SPI communication Fault (F18) on KStar KSG-15K?
- R
  Robert ScottSep 7, 2025
  If your KStar Inverter is showing an SPI communication Fault (F18), try the following: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
R
rsimmonsSep 5, 2025
How do I fix an AC Relay Fault (F14) on my KStar Inverter?
- L
  Leslie JohnsSep 5, 2025
  If your KStar Inverter is showing an AC Relay Fault (F14), try these steps: 1. Disconnect the PV input and restart the inverter to see if the fault clears. 2. If the fault persists, contact your local distributor.
L
Lindsay StoneAug 20, 2025
How to fix AC voltage or frequency too high/low on KStar Inverter (F00-F03)?
- H
  Howard WadeAug 20, 2025
  If your KStar Inverter displays an F00-F03 error, indicating that the AC voltage or frequency is too high or too low, take the following steps: 1. Verify that the mains voltage complies with the local safety standards. 2. Ensure the AC output line is properly connected and check if its output voltage is normal. 3. Disconnect the PV input, restart the inverter, and check if the fault persists. 4. If the fault continues, it is recommended to contact your local distributor.