Why aren't the turn signal, brake light, and horn working on my KTM Motorcycle?
If the turn signal, brake light, and horn are not working on your KTM Motorcycle, it could be due to a blown fuse 6. Change the fuses to resolve this.
Why does my KTM 125 DUKE EU engine only turn if the clutch lever is drawn?
If your KTM Motorcycle engine only turns when the clutch lever is drawn, it's likely that the vehicle is in gear. Shift the gear to neutral. It could also be that the vehicle is in gear and the side stand is folded out, so shift to neutral.
General| Displacement | 124.7 cc |
|---|---|
| Bore x Stroke | 58 mm x 47.2 mm |
| Torque | 12 Nm @ 7, 500 rpm |
| Starter | Electric starter |
| Transmission | 6-speed |
| Fuel System | Electronic Fuel Injection |
| Frame | Steel trellis frame |
| Front Wheel | 3.00 x 17" |
| Rear Wheel | 4.00 x 17" |
| Front Tire | 110/70-17 |
| Rear Tire | 150/60-17 |
| Seat Height | 830 mm |
| Fuel Tank Capacity | 13.4 liters |
| Engine Type | Single-cylinder, 4-stroke |
| Power | 15 hp |
| Rear Suspension | Monoshock |
| Front Brake | Disc brake, 300 mm |
| Rear Brake | Single 230 mm disc, single-piston caliper |
Explains the meaning of specific symbols used in the manual.
Explains the typographical formats used in the document.
Defines the intended use of KTM sport motorcycles.
General advice on operating the vehicle safely and warning labels.
Identifies different risk levels and their associated symbols.
Prohibits tampering with the noise control system and lists prohibited acts.
Covers dangers of accidents, poisoning, and burns, and general safe operation.
Emphasizes the importance of wearing protective clothing for safety.
Details rules for assembly, part replacement, and checks after service.
Advises on responsible use and disposal of fluids and components.
Stresses reading the manual for information on operation, handling, and maintenance.
Outlines requirements for maintaining warranty and voiding claims.
Warns about environmental hazards of fuel handling and specifies substance use.
Recommends using approved KTM parts and accessories for safety.
Emphasizes proper service, care, and tuning for operation and wear prevention.
Notes that manual figures may show special equipment or disassembled parts.
Directs users to authorized KTM dealers for questions and lists the website.
Illustrates and labels various components of the motorcycle from the front left view.
Illustrates and labels various components from the rear right view of the motorcycle.
Shows the location of the chassis number and type label on the motorcycle.
Shows the location of the engine number on the motorcycle.
Explains where to find the key number and its importance for ordering spare keys.
Identifies the location and function of the clutch lever on the handlebar.
Identifies the location of the hand brake lever and its use for the front brake.
Identifies the location of the throttle grip on the handlebar.
Identifies the location and possible states of the horn button.
Explains the location and possible states (low beam/high beam) of the light switch.
Identifies the location and possible states of the high beam flasher button.
Identifies the location and possible states of the turn signal switch.
Identifies the location and possible states of the emergency OFF switch.
Identifies the location and possible states of the electric starter button.
Explains the location and possible states of the ignition and steering lock.
Provides an overview of the combination instrument, labeling its main components.
Labels the main display elements: display, function buttons, info display, and indicator lamps.
Describes the activation sequence and self-test of the combination instrument.
Explains warning messages displayed for low oil pressure and low fuel level.
Explains warning messages for high coolant temperature, side stand down, and low battery.
Explains the 'Service Not Reset' warning message.
Explains how to change display modes and reset trip functions using buttons.
Describes the various indicator lamps on the instrument cluster and their meanings.
Explains the different segments of the digital display and their functions.
Describes how the fuel level is indicated by bars on the display.
Explains the TRIP F display mode when the fuel level is low.
Explains the coolant temperature display and its possible states.
Describes how warning notes are displayed in the info display.
Explains how to view riding time and average speed.
Explains how to view average speed and fuel consumption 1.
Explains how to view average fuel consumption 1 and 2.
Explains how to view average fuel consumption 2 and distance to next service.
Explains how to view distance to next service and the vehicle's range.
Explains how to view the vehicle's range and riding time.
Explains how to display the total distance covered (ODO).
Explains the TRIP 1 function for measuring distance since last reset.
Explains the TRIP 2 function for measuring distance since last reset.
Describes how to set the unit of distance (km/miles).
Details the procedure for setting the time on the instrument cluster.
Explains how to set the engine speed for the shift warning light (RPM 1).
Explains how to set the engine speed for the shift warning light (RPM 2).
Provides instructions and safety warnings for opening the fuel filler cap.
Details the procedure for properly closing the fuel filler cap with safety warnings.
Shows the location of the seat lock and how to use the ignition key to lock it.
Indicates the location of the tool set under the passenger seat.
Describes the purpose of the grab handles for maneuvering and passenger use.
Explains the passenger footrests and their possible states (up/down).
Identifies the location of the shift lever on the engine.
Identifies the location of the foot brake lever and its function for the rear brake.
Describes the location and function of the side stand and its coupling with the safety start system.
Provides general advice and warnings for the initial use of the motorcycle.
Details the procedure and guidelines for running in the engine, including max engine speed.
Provides warnings and guidelines regarding vehicle loading and weight limits.
Lists essential checks and maintenance steps before riding.
Provides instructions and safety warnings for starting the motorcycle's engine.
Explains the procedure for starting to ride the motorcycle.
Provides warnings and advice on shifting gears and general riding practices.
Offers warnings and advice on proper braking techniques and potential issues.
Provides instructions and warnings for stopping and parking the motorcycle safely.
Gives advice on safely transporting the motorcycle.
Provides instructions and safety warnings for refueling the motorcycle.
Lists maintenance tasks and their recommended intervals (km/years).
Explains how to adjust the spring preload on the shock absorber for different loads.
Details the procedure for adjusting the shift lever's position.
Explains how to safely lift the motorcycle using a rear wheel stand.
Explains how to safely lower the motorcycle from a rear wheel stand.
Details the procedure for raising the motorcycle using a front wheel stand.
Explains how to safely lower the motorcycle from a front wheel stand.
Provides steps for removing the passenger seat.
Explains how to properly mount the passenger seat.
Details the procedure for removing the main seat.
Provides instructions for mounting the main seat, including torque specifications.
Describes how to check the chain for dirt and when cleaning is necessary.
Details the process for cleaning the motorcycle's chain with warnings about oil and grease.
Explains how to check the chain tension and the consequences of incorrect tension.
Details how to adjust the chain tension and the importance of correct tension.
Guides on checking wear on the chain, rear sprocket, and engine sprocket.
Provides instructions for removing the front spoiler.
Provides instructions for fitting the front spoiler, including torque specs.
Explains the ABS unit, its function, limitations, and warnings.
Details how to check the brake discs for wear and damage.
Guides on checking the front brake fluid level and associated warnings.
Explains how to add front brake fluid with safety precautions.
Details how to check the minimum thickness of front brake linings.
Explains how to check the free travel of the foot brake lever.
Provides instructions for adjusting the free travel of the foot brake lever.
Guides on checking the rear brake fluid level and associated warnings.
Explains how to add rear brake fluid with safety precautions.
Details how to check the minimum thickness of rear brake linings.
Provides step-by-step instructions for removing the front wheel.
Details the procedure for installing the front wheel.
Provides step-by-step instructions for removing the rear wheel.
Details the procedure for installing the rear wheel.
Explains how to check the rear hub rubber dampers for wear.
Guides on checking tire condition, including cuts, damage, and tread depth.
Details how to check tire air pressure for solo and passenger/payload conditions.
Provides instructions and warnings for safely removing the motorcycle battery.
Details the procedure for installing the motorcycle battery.
Explains how to recharge the battery and provides warnings about battery acid.
Details how to change the ABS fuses with warnings about electrical system overload.
Guides on changing fuses for various power consumers and identifies fuse box location.
Provides instructions for changing the headlight bulb.
Provides instructions for changing the parking light bulb.
Explains how to check and verify the headlight alignment.
Details how to adjust the headlight beam distance for proper range.
Explains the basic function of the cooling system and its components.
Provides instructions and warnings for checking the antifreeze and coolant levels.
Details how to check the coolant level in the radiator and compensating tank.
Provides instructions and safety warnings for draining the coolant.
Explains how to fill and bleed the cooling system.
Explains how to check the throttle cable play and idle speed.
Details how to adjust the play in the throttle cable.
Explains how to check the clutch lever play and its importance.
Details how to adjust the play in the clutch cable.
Guides on how to check the engine oil level.
Provides instructions for changing engine oil, filter, and cleaning the oil screen.
Explains how to add engine oil, including oil types and capacities.
Provides guidelines and warnings for cleaning the motorcycle, especially with pressure washers.
Outlines checks and maintenance for winter operation, focusing on road salt corrosion.
Lists steps for preparing the motorcycle for long-term storage.
Details the procedure for preparing the motorcycle after a period of storage.
Provides a troubleshooting guide for common engine and electrical issues.
Lists detailed technical specifications for the engine.
Provides specific engine data for the 125 Duke model.
Provides specific engine data for the 200 Duke EU/MAL models.
Lists torque specifications for various engine components.
Lists various fluid capacities for the motorcycle.
Specifies engine oil types, quantities, and temperature ranges.
Specifies coolant type and quantity.
Lists fuel tank capacity and reserve.
Details chassis specifications like frame, fork, suspension, and brake system.
Lists battery types, fuses, headlights, and indicator lamp specifications.
Lists torque specifications for various chassis components.
Lists recommended substances like brake fluid, coolant, and engine oil.
Lists auxiliary substances like chain cleaner, lube, and fuel additive.
Explains JASO T903 MA and SAE standards for engine oils.
To Next Page
