Kverneland EO - User Manual

Questions and Answers

S
Spencer CochranAug 12, 2025
Why is the first furrow width different on left and right sides with Kverneland Farm Equipment?
- B
  Brandon FischerAug 12, 2025
  If the first furrow width is different when ploughing on the left and right hand sides with your Kverneland Farm Equipment, there might be a few reasons. It could be that the drag axle isn't positioned centrally on the turning head, so ensure you position the drag axle over the turning head. Also, check that the air pressure in the tractor’s rear tires is equal and adjust if necessary. Finally, incorrect sideways leveling can cause this issue, so make sure to adjust the leveling.
J
jeffreylopezAug 16, 2025
How to fix a Kverneland EO Farm Equipment plough that will not start turning?
- F
  francisco53Aug 16, 2025
  If your Kverneland Farm Equipment plough won't start turning, it's possible that the connections to the tractor are mounted incorrectly. Check that the quick–couplings are properly engaged and correctly connected, paying attention to the color coding on the hoses.
K
Kathleen HowardAug 19, 2025
Why is turning a slow process on heavy Kverneland Farm Equipment ploughs?
- T
  Travis MeyerAug 19, 2025
  If turning is a slow process on heavy Kverneland Farm Equipment ploughs and may not be completed, the issue could be incorrect oil flow. Try adjusting the motor speed or flow rate on the tractor valve to see if it affects the turnover. Switch-over valves operate optimally at 25-35 l/min. High flow rate may rise return pressure, causing poorer turnover performance.
L
Lisa MahoneyAug 23, 2025
What to do if Kverneland EO Farm Equipment plough turns halfway and then stops?
- A
  Antonio MillerAug 23, 2025
  If the Kverneland Farm Equipment plough turns halfway and then stops, or returns to the start position, it could be due to the restrictor being mounted in the wrong port. Change the restrictor position. Another potential cause is incorrect switch pressure. Try increasing or reducing the switch pressure.
R
ronald06Aug 27, 2025
Why does the turning cylinder creep during ploughing with Kverneland EO?
- A
  aimeereynoldsAug 27, 2025
  If the Kverneland Farm Equipment turning or alignment cylinder creeps during ploughing or transport, it could be because the turning phase isn't completed and the cylinder isn't locked. Complete the turning phase and apply the turning pressure. On ploughs with a memory system, any adjustment of the working width should be carried out using the vari-width lever, not the turning lever. Alternatively, the seal in the turnover cylinder could be leaking, or there could be a leakage in the turning valve, in which case you should contact your dealer.
R
rosetamiAug 31, 2025
What causes turning to stop in the first cycle on Kverneland Farm Equipment with Packomat?
- O
  Olivia Mullen MDAug 31, 2025
  If the turning stops in the first turning cycle with a Kverneland Farm Equipment plough with Packomat, or when turning the plough with the bodies under the main frame, the switch-over may be taking place prematurely, just before dead center is reached. Increase the transfer pressure setting by turning a few times clockwise and ensure that the restrictor in the turning cylinder is correctly positioned.
R
richard09Sep 3, 2025
Why are there vibrations during turning with Kverneland EO?
- D
  Daniel MartinezSep 4, 2025
  If vibrations occur during turning with your Kverneland Farm Equipment, the restrictor might be mounted in the wrong port. You should change the restrictor position.
J
Jessica CrawfordSep 7, 2025
What to do if Kverneland EO plough won't start reversing?
- A
  Alison HerreraSep 7, 2025
  If the Kverneland Farm Equipment plough will not start reversing and reacts with a suddenly interrupted start only when applying oil pressure to the turnover valve, the switch pressure may be wrong. Increase the transfer pressure setting by turning a few times clockwise.