3 / 4
Conirm that the code(s) added in previous step can unlock the door.
Option 1
Touch screen with
palm or back of
hand until digits
illuminate.
Option 2
Touch lower left
area of screen
(where checkmark
is located) until
digits illuminate.
Option 3
Touch screen
with three or
more ingers until
digits illuminate.
Activating the Screen Locking the Door Unlocking the Door SecureScreen™
1. Activate the screen.
2. Press Lock symbol.
Note: If no user codes
are programmed, the
door cannot be locked
via touchscreen.
1. Activate the screen.
2. If SecureScreen™ is enabled, touch
the random digits that appear.
3. Enter user code.
If you press the wrong digit while entering
a user code, you can press the Lock symbol
once to clear the digits entered previously and
immediately restart the code entry process.
If desired, this feature
can be disabled by
turning switch #4 to
the o position. See
“Switches” on page 4.
SecureScreen is an added-security feature
that displays random digits before you enter
a user code to unlock the door. This feature
ensures that there are ingerprints on all
digits so that codes cannot be identiied by
examining the touchscreen for inger prints.
Test the lock (review normal operation)
Initiate the pairing process at your smart
home controller. Refer to your smart home
system instructions for more information.
When prompted by your smart home
system to initiate pairing at the lock, press
button “A” on the lock interior four times.
If the pairing process is successful, re-name the
lock in your system (if applicable).
If the pairing process is unsuccessful, press button “B” nine times.
Perform steps 7A7C again.
If pairing is still unsuccessful, consult the Programming and
Troubleshooting Guide on the SmartCode 916 page at www.kwikset.com.
A B C
D
button “A” button “B”
Pair the lock with your smart home system
7
8
9
Add user codes (30 max)
1x 3x
Checkmark symbol with one beep “X” pattern with three beeps
or
Make sure the door
is open. Press the
Program button once.
Press checkmark
symbol once.
Enter user code. A total
of 30 user codes may
be programmed.
Press lock symbol once.
BA C D E
What digits and sounds did the lock produce?
F
Programming information
Mastercode: For enhanced security, a
mastercode may be used when adding and
deleting user codes. For more information
about the mastercode, download the
SmartCode 916 Programming and
Troubleshooting Guide at www.kwikset.com.
Programming Timeout :During
programming, if the screen is not pressed
for 20 seconds, the system will time out
(indicated by three beeps and the “X” pattern
lashing three times), and you will need to
restart the procedure.
Programming was successful. Programming was unsuccessful.
Each user code must be
a unique code between 4
and 8 digits, depending on
your smart home system.
*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.
It is recommended that you add and delete all user codes through your smart home system.
If your system does not allow this, codes may be added directly to the lock as shown here.
Move swiftly through
programming, as the system
will time out if no button is
pressed for 20 seconds.
Make sure the user code is
not a duplicate and that it
is between 4 and 8 digits
during your next attempt.
Make sure the lock has
room for an additional code.
If all user code positions
are illed, delete a code to
make room for this one.
Install the battery cover.
M
V (x3)
a
b
IMPORTANT:
Remove battery
pack before
re-keying.
K
H
K
a
b
c
Re-key the lock
to work with your
existing key. See
the supplied
SmartKey Re-key
instructions for
more information.
Reinstall
battery
pack.
Optional: Re-key the lock.
A B
V
actual
size
10
Re-key the lock (if needed) and install the battery cover
To Next Page
Loading...
