Kyocera TASKalfa 180 User Manual (English)

Other manuals for Kyocera TASKalfa 180

Operation Guide164 pages

Installation Guide2 pages

Quick Guide2 pages

Specifications87 pages

Questions and Answers:

A
Alyssa BrownAug 25, 2025
How to fix light printouts on Kyocera TASKalfa 180 All in One Printer?
- J
  James VargasAug 25, 2025
  If your Kyocera All in One Printer's printouts are too light, and the machine is in Auto Density mode, set the correct density level. If the machine is in Manual Density mode, use the Image Quality key to set the correct density level. Make sure the toner is distributed evenly within the toner container by shaking it from side to side several times. Replace the toner container if there's a message indicating the need for toner. Replace damp paper with new paper. Clean the electrical charge section using the Cleaning Rod after opening the front cover. Also, disable EcoPrint mode.
T
Tanya JacksonAug 25, 2025
Why are the printouts from my Kyocera TASKalfa 180 dirty?
- V
  vanessagoodmanAug 26, 2025
  If your Kyocera All in One Printer's printouts are dirty, the platen or the original cover might be dirty. Clean the platen or the original cover. Also, the transfer roller might be dirty, so brush the transfer roller clean.
D
Diana PetersAug 27, 2025
What to do when Kyocera TASKalfa 180 says 'Add toner'?
- C
  Catherine MyersAug 27, 2025
  If your Kyocera All in One Printer indicates 'Add toner', replace the toner container with a new one.
M
Marc AguirreAug 28, 2025
What to do if pressing Start key on Kyocera TASKalfa 180 doesn't make copies?
- T
  Tammy HodgesAug 28, 2025
  If pressing the Start key on your Kyocera All in One Printer doesn't produce copies, it could be due to a message on the touch panel. Determine the appropriate response to the message and respond accordingly. Alternatively, the printer might be in Sleep mode. Press the Power key to recover the machine from Sleep mode, and it will be ready to copy within 1 second.
R
rogerkimSep 12, 2025
How to remove moire pattern on Kyocera TASKalfa 180 All in One Printer copies?
- S
  stephaniethompsonSep 12, 2025
  If you see a moire pattern on copies from your Kyocera All in One Printer, and the original is a printed photograph, set the image quality mode to 'Photo'.
M
Maria LongSep 12, 2025
How to fix vertical lines on Kyocera All in One Printer copies?
- Z
  Zachary AndersonSep 12, 2025
  If black or white vertical lines appear on copies from your Kyocera All in One Printer, the electrical charge section might be dirty. Open the front cover and use the charger cleaner rod to clean it.
D
duncanjackSep 12, 2025
Why are my Kyocera All in One Printer copies blank?
- A
  Ashley ColeSep 12, 2025
  If your Kyocera All in One Printer copies come out blank, ensure the originals are set correctly. When using the platen, place them face-down along the original size indicator plates. If using the document processor, set them face-up.
M
munozbarbaraSep 4, 2025
Why are my Kyocera All in One Printer copies too light?
- R
  Regina MeyersSep 4, 2025
  If your Kyocera All in One Printer copies are too light, several factors could be the cause: * The auto density adjustment mode might be enabled. To resolve this, perform the auto density adjustment procedure. * If the manual density mode is set, use the Lighter or Darker key to adjust the density. * The toner may not be evenly distributed. Shake the toner container horizontally about 10 times. * EcoPrint mode might be activated; disable it. * The copy paper might be wet; replace it with new paper. * The electrical charge section could be dirty; open the front cover and clean it with the charger cleaner rod.
H
Heather MeyerSep 2, 2025
Why are my Kyocera TASKalfa 180 printouts wrinkled?
- Y
  yguzmanSep 2, 2025
  If your Kyocera All in One Printer produces wrinkled printouts, the paper separator of the paper feed unit might be dirty; clean the paper separator. Also, if the paper is damp, replace it with new paper.
D
David MoralesSep 3, 2025
How to fix moire pattern on Kyocera TASKalfa 180 All in One Printer copies?
- R
  Robert GentrySep 3, 2025
  If your Kyocera All in One Printer copies have a moire pattern, and the original is a printed photograph, select “Photos” in the Image Quality Mode.

Kyocera TASKalfa 180 Specifications

General

Duplex printing	No
Print technology	Laser
Maximum resolution	2400 x 600 DPI
Economical printing	Yes
Time to first page (black, normal)	5.7 s
Print speed (black, normal quality, A3)	8 ppm
Print speed (black, normal quality, A4/US Letter)	18 ppm
Safety	TÜV/GS, CE
Media thickness	0.11 mm
Dimensions (WxDxH)	568 x 546 x 502 mm
All-in-one functions	Copy, Print
Compatible operating systems	Windows 98 SE/ME/2000/XP/Vista
Maximum duty cycle	- pages per month
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	999 copies
Grayscale levels	256
Optical scanning resolution	- DPI
Total input capacity	300 sheets
Total output capacity	250 sheets
Maximum input capacity	1300 sheets
Multi-Purpose tray input capacity	100 sheets
Maximum print size	297 x 420 mm
Paper tray media types	Plain paper
Non-ISO print media sizes	Folio
ISO A-series sizes (A0...A9)	A3, A4, A5, A6
Maximum ISO A-series paper size	A3
Display	-
Market positioning	Business
Standard interfaces	USB 2.0
USB 2.0 ports quantity	1
Processor family	ARM9E
Processor frequency	150 MHz
Sound pressure level (printing)	65.3 dB
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	60 W
Power consumption (average operating)	424 W
Sustainability certificates	ENERGY STAR