Kyocera TASKALFA FS-1100

Questions and Answers

M
Michael JacksonSep 22, 2025
Why is Kyocera Software not discovering the printing system?
- K
  kbradySep 22, 2025
  The printing system might be turned off, so turn it on and try again. It could also be removed from the network, so ensure it's connected. If the system is currently printing, wait until it's finished and then try searching again. It is also possible that the TCP/IP settings on your PC are not configured properly, in that case contact your network administrator. Depending on the network router configuration, a printing system may be undetectable. In some rare cases, heavy network traffic may prevent this application from detecting the printing systems, so try again later or contact your network administrator.
L
Lisa ObrienAug 25, 2025
How to fix light printouts on Kyocera All in One Printer?
- T
  Tara HinesAug 25, 2025
  If your Kyocera All in One Printer's printouts are too light, and the machine is in Auto Density mode, set the correct density level. If the machine is in Manual Density mode, use the Image Quality key to set the correct density level. Make sure the toner is distributed evenly within the toner container by shaking it from side to side several times. Replace the toner container if there's a message indicating the need for toner. Replace damp paper with new paper. Clean the electrical charge section using the Cleaning Rod after opening the front cover. Also, disable EcoPrint mode.
O
Olivia JohnsonAug 25, 2025
Why are the printouts from my Kyocera TASKALFA FS-1100 All in One Printer dirty?
- J
  Jennifer DavisAug 26, 2025
  If your Kyocera All in One Printer's printouts are dirty, the platen or the original cover might be dirty. Clean the platen or the original cover. Also, the transfer roller might be dirty, so brush the transfer roller clean.
M
michael59Aug 27, 2025
What to do when Kyocera TASKALFA FS-1100 All in One Printer says 'Add toner'?
- T
  Terry HenryAug 27, 2025
  If your Kyocera All in One Printer indicates 'Add toner', replace the toner container with a new one.
M
Michael DouglasSep 23, 2025
What to do if Kyocera Software application does not start?
- B
  Brian LarsonSep 23, 2025
  If the Kyocera Software application doesn't start, it could be due to several reasons. First, your PC might not meet the necessary system requirements; in this case, consider upgrading your PC. Another possibility is low memory; try closing any unnecessary applications. Also, ensure that you are not trying to run two instances of the application simultaneously, as this is not supported.
S
scott68Nov 26, 2025
What to do if Kyocera TASKALFA FS-1100 network connection fails?
- M
  Melissa RodgersNov 26, 2025
  If a network connection fails, for example, indicated by a Send Error, try the following: * Connect the network cable and properly set up TCP/IP. * Check folder sharing and access permissions in the Folder Properties dialog box. * Enable the SMB protocol setting. * Verify the host name of the destination computer and the name of the shared folder. * Confirm the domain name and domain user name are correct. * Ensure the login password is correct. * If the domain name specified in [Host Name] differs from the one specified in [Login User Name], delete the domain name and a \\ from the name entered in [Login User Name]. * Also, ensure the time setting is the same between the machine, PC, and the domain server. * To configure Windows Firewall, open Control Panel from the Sta...
G
Gregory GutierrezSep 12, 2025
How to fix vertical lines on Kyocera All in One Printer copies?
- P
  pattersondavidSep 12, 2025
  If black or white vertical lines appear on copies from your Kyocera All in One Printer, the electrical charge section might be dirty. Open the front cover and use the charger cleaner rod to clean it.
M
Michael BrownSep 12, 2025
Why are my Kyocera TASKALFA FS-1100 All in One Printer copies blank?
- C
  Charles SandersSep 12, 2025
  If your Kyocera All in One Printer copies come out blank, ensure the originals are set correctly. When using the platen, place them face-down along the original size indicator plates. If using the document processor, set them face-up.
T
Tara WhiteheadSep 4, 2025
Why are my Kyocera TASKALFA FS-1100 All in One Printer copies too light?
- C
  Christina DiazSep 4, 2025
  If your Kyocera All in One Printer copies are too light, several factors could be the cause: * The auto density adjustment mode might be enabled. To resolve this, perform the auto density adjustment procedure. * If the manual density mode is set, use the Lighter or Darker key to adjust the density. * The toner may not be evenly distributed. Shake the toner container horizontally about 10 times. * EcoPrint mode might be activated; disable it. * The copy paper might be wet; replace it with new paper. * The electrical charge section could be dirty; open the front cover and clean it with the charger cleaner rod.
M
Mary FullerSep 2, 2025
Why are my Kyocera All in One Printer printouts wrinkled?
- V
  Victor BaxterSep 2, 2025
  If your Kyocera All in One Printer produces wrinkled printouts, the paper separator of the paper feed unit might be dirty; clean the paper separator. Also, if the paper is damp, replace it with new paper.

Kyocera TASKALFA FS-1100 Specifications

General

Technology	Laser
Maximum resolution	1200 x 1200 DPI
Standard output capacity	250 sheets
Duplex Printing	Yes
Paper size (tray 1)	A4
Print media types	Plain paper, Recycled paper
Standard interfaces	USB 2.0
Product colour	White
Functions	Print
Copy Resolution	600 x 600 dpi
Scan Resolution	600 x 600 dpi
Operating System Compatibility	Windows