Why are my Kyocera TASKALFA FS-1100 All in One Printer copies blank?
If your Kyocera All in One Printer copies come out blank, ensure the originals are set correctly. When using the platen, place them face-down along the original size indicator plates. If using the document processor, set them face-up.
How to fix vertical lines on Kyocera All in One Printer copies?
If black or white vertical lines appear on copies from your Kyocera All in One Printer, the electrical charge section might be dirty. Open the front cover and use the charger cleaner rod to clean it.
Why are my Kyocera TASKALFA FS-1100 copies curled?
If your Kyocera All in One Printer copies are curled, it could be due to wet copy paper; replace it with dry, new paper. Also, if 'Middle 2' is set at the Paper type (Paper Weight) setting, change it to 'Middle 1'.
How to clean Kyocera TASKALFA FS-1100 All in One Printer for dirty copies?
If your Kyocera All in One Printer produces dirty copies, the platen or the original cover might be dirty. Clean the platen and/or the original cover to resolve this issue.
Why does my Kyocera TASKALFA FS-1100 All in One Printer paper jam so often?
If your Kyocera All in One Printer often experiences paper jams, ensure the paper is loaded correctly. Also, check if the paper is of the supported type and in good condition; try removing the paper, turning it over, and reloading it. Replace curled, folded, or wrinkled paper with new paper. Finally, remove any loose scraps or jammed paper from the machine.
How to fix skewed copies on Kyocera TASKALFA FS-1100?
If your Kyocera All in One Printer is producing skewed copies, make sure the originals are set correctly. When using the platen, securely align the original along the original size indicator plates. Also, check the width guide plate position in the cassette to ensure the paper is set correctly.
Why are my Kyocera TASKALFA FS-1100 All in One Printer copies too dark?
If your Kyocera All in One Printer copies are too dark, it might be due to the auto density adjustment mode being enabled. To correct this, perform the auto density adjustment procedure. Alternatively, if the manual density mode is set, use the Lighter key or the Darker key to properly adjust the density level.
Why are my Kyocera TASKALFA FS-1100 All in One Printer copies too light?
If your Kyocera All in One Printer copies are too light, several factors could be the cause: * The auto density adjustment mode might be enabled. To resolve this, perform the auto density adjustment procedure. * If the manual density mode is set, use the Lighter or Darker key to adjust the density. * The toner may not be evenly distributed. Shake the toner container horizontally about 10 times. * EcoPrint mode might be activated; disable it. * The copy paper might be wet; replace it with new paper. * The electrical charge section could be dirty; open the front cover and clean it with the charger cleaner rod.
How to fix moire pattern on Kyocera TASKALFA FS-1100 copies?
If your Kyocera All in One Printer copies have a moire pattern, and the original is a printed photograph, select “Photos” in the Image Quality Mode.
Why are my Kyocera All in One Printer printouts wrinkled?
If your Kyocera All in One Printer produces wrinkled printouts, the paper separator of the paper feed unit might be dirty; clean the paper separator. Also, if the paper is damp, replace it with new paper.
General| Technology | Laser |
|---|---|
| Maximum resolution | 1200 x 1200 DPI |
| Standard output capacity | 250 sheets |
| Duplex Printing | Yes |
| Paper size (tray 1) | A4 |
| Print media types | Plain paper, Recycled paper |
| Standard interfaces | USB 2.0 |
| Product colour | White |
| Functions | |
| Copy Resolution | 600 x 600 dpi |
| Scan Resolution | 600 x 600 dpi |
| Operating System Compatibility | Windows |
To Next Page