What to do if LaMotte SMART3 Measuring Instruments display 'Low Battery'?
If your LaMotte Measuring Instruments display 'Low Battery', the battery voltage is very low. To resolve this, charge the battery or use a USB wall/computer adapter.
What to do if LaMotte Measuring Instruments say 'Shut Down Low Batt'?
If your LaMotte Measuring Instruments display 'Shut Down Low Batt', it means the battery is too low to operate the unit. Charge the battery or use a USB wall/computer adapter.
What to do if LaMotte SMART3 have large negative or positive readings during calibration?
If you get unusually large negative or positive readings when calibrating your LaMotte Measuring Instruments, it could be due to incorrect standards. Use fresh 0.0 standard in a clean tube, reset the meter to factory default settings, and then recalibrate the meter.
What to do if LaMotte SMART3 show 'Low Battery'?
If your LaMotte Measuring Instruments display 'Low Battery,' it means the battery voltage is very low, and the readings may not be reliable. Charge the battery or use a USB wall/computer adapter.
Why LaMotte SMART3 show 'Shut Down Low Batt' and shut down?
If your LaMotte Measuring Instruments shut down and display 'Shut Down Low Batt', it means the battery is too low to operate the unit. You should charge the battery or use a USB wall/computer adapter.
How to fix large readings during LaMotte SMART3 calibration?
If you are getting unusually large negative or positive readings when calibrating your LaMotte Measuring Instruments, it is likely due to incorrect standards. Use a fresh 0.0 standard in a clean tube. You may also need to reset the meter to factory default settings and then recalibrate it.
What to do if LaMotte SMART3 Measuring Instruments show 'Overrange'?
If your LaMotte Measuring Instruments display shows 'Overrange', it means the sample you are testing is outside the acceptable range. To fix this, dilute the sample and test it again.
What to do if LaMotte SMART3 say 'No printer connected'?
If your LaMotte colorimeter indicates 'No printer connected', it means the colorimeter hasn't been paired via Bluetooth or the pairing was lost. To solve this, re-pair the colorimeter to the printer.
Why is my LaMotte Measuring Instruments flashing?
If your LaMotte Measuring Instruments are flashing, it usually means the battery is low. You can resolve this by charging the battery or using a USB wall/computer adapter.
Why does printer not appear in the list of Bluetooth devices for LaMotte SMART3 Measuring Instruments?
If the printer does not appear in the list of Bluetooth devices for your LaMotte Measuring Instruments, it might not be powered on. Ensure the printer is powered on.
Details on how shipments are packaged and responsibilities for safe delivery.
Important instructions before setup or operation to prevent injury or damage.
Guidelines for handling reagent containers and keeping chemicals away from children.
Outlines the terms and conditions of the instrument's warranty coverage.
Provides guidelines for collecting representative water samples for analysis.
Explains the principles of colorimetry and how colorimeters measure light absorption.
Recommends periodic verification of meter performance with standards.
Details the process of creating calibration curves for reagent systems.
Discusses factors that can affect test results and how reagent systems minimize them.
Introduces the SMART3 as a portable, microprocessor-controlled colorimeter.
Illustrates and describes the physical parts and connections of the SMART3 Colorimeter.
Explains the function of each of the 6 buttons used for meter operation.
Details how menu selections are viewed and navigated on the display.
Explains how to run pre-programmed, user, and absorbance tests.
Describes how to create and use alterable test sequences for frequent tests.
Details the procedure to standardize pre-calibrated tests for accurate readings.
Allows editing of three alterable test sequences (Sequence 1, 2, 3).
Guides on entering and managing custom test calibrations and settings.
Guides choosing the correct vial and wavelength combination for a test.
How to interface the SMART3 with a computer using SMARTLink 3 software.
Details the data recorded by SmartLink3, including test ID and serial number.
Explains operating the meter on battery or AC power and charging.
Proper methods for cleaning the exterior and optical areas of the meter.
Instructions for returning the meter for repair, including necessary information.
Explains common error messages like OVERRANGE and their solutions.
A table listing common problems, their reasons, and solutions.
Details proper sampling techniques and how to 'fix' the sample for testing.
Daily preparation instructions for the TMK Indicator solution.
General| Brand | LaMotte |
|---|---|
| Model | SMART3 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
