Lampert PUK5.1 - 13 Disposal Information; 14 EC Declaration of Conformity

Lampert Werktechnik GmbH Lampert Werktechnik GmbH
OPERATING MANUAL PUK 5.1
EN
Fault occurring Possible cause Fault rectification
Electrode welds to workpiece Pressure of the electrode on
theworkpiece too great
Touch workpiece with extremely
light pressure
Electrode tip melts Electrode abraded too steeply Correct the angle of electrode
abrasion, see “Abrading
theelectrodes”, approx. 15°
recommended
Static discharge over the surface
of the device
Static charge from the environment Use antistatic foot mat in theworking
area, use antistatic cables
Welding process begins, but a
welding point is not produced
Internal protective circuit is
triggered
Switch device off and back on
again
Welding process is triggered
immediately when touching
theworkpiece
Malfunction Immediately put the device out of
operation, contact customer
service
Faults on the microscope
LED illumination fails to operate Cable not connected Connect the plug to the connection
socket marked with the red and
yellow eye protection / lamp
symbol on the device
LED faulty Contact customer service
Eye protection system (shutter)
fails to operate
Plug not connected correctly Connect the plug to the connection
socket marked with the red and
yellow eye protection / lamp
symbol on the device
Eye protection filter faulty Arrange to have eye protection unit
replaced by qualified personnel
Poor resolution Oculars dirty Clean oculars
Marks or soiling in field of vision Oculars dirty Clean oculars, marks in the field
ofvision can also be caused by
soiling in the interior of theoculars.
For this reason, itisrecommended
to have the lenses cleaned by
aqualified specialist
Protective glass dirty Clean protective glass
Undesired focussing changes occur
and attachment slides down
independently
Attachment not fitted correctly Check fastening and re-tighten
12. Repair and guarantee
If the welding device or welding microscope require repair, overhaul or adjustment, your specialist dealer
orauthorised customer service centre should be your first point of contact.
The device may only be opened by a qualified specialist!
The guarantee provisions are always binding. Excluded from the guarantee are hand pieces, wearing parts
such as nozzles, clamping nuts, electrodes and chucks.
13. Disposal information
Render discarded devices unusable by removing the mains cable.
Only for EU countries: In accordance with European directive 2012/19/EU regarding the disposal
of used electrical and electronic equipment, discarded electrical devices must be separated
andcollected and sent for recovery in an environmentally friendly manner.
14. EC Declaration of Conformity
The manufacturer Lampert Werktechnik GmbH, Ettlebener Str. 27, 97440 Werneck, Germany
declares herewith that the following products:
Fine welding device PUK5.1 including PUK eye protection system comply with the stipulations of the directives
identified below - including any changes applicable at the time of this declaration.
Applicable EC directives are:
♦ Low Voltage Directive 2014/35/EU
♦ EMC Directive 2014/30/EU
♦ Machinery Directive 2006/42/EC
♦ Directive governing personal protective equipment 89/686/EEC
♦ RoHS-Directive 2011/65/EU
The following harmonised standards have been applied:
♦ EEN 50581:2012
♦ EN 60974-6:2016
♦ EN ISO 12100:2010
♦ EN 61000-6-1:2007, EN 61000-6-3:2007+A1:2011
♦ EN 61000-3-2:2014, EN 61000-3-3:2013
♦ EN 379:2003+A1:2009
Werneck, January 2019
Lampert Werktechnik GmbH
Martin Beckmann (Dipl.-Wirtschafts-Ing.), Managing Director
Text and illustrations represent the technical status at the time of printing. Subject to change.
30