Lenze E82EV113K4C - Page 30

Total index
2
Guide
2.3
L
2.3-8
EDS82EV903-1.0-11/2002
Process controller, 10.10-1
- ”Debouncing” of digital output signal PCTRL1-LIM,
10.20-20
- ”Debouncing” of digital output signal
PCTRL1-SET=ACT , 10.20-20
- Activation of inverse control, 10.20-21
- Actual root function value, 10.20-21
- Control characteristics, 10.10-1
- Delay PCTRL1-LIM=HIGH, 10.20-20
- Delay PCTRL1-SET=ACT, 10.20-20
- Difference threshold PCTRL1-SET=ACT, 10.20-21
- Hide time, 10.20-20
- hiding/unhiding, 10.20-21
- Integral action component switch-off, 10.10-7
- Max. limit output, 10.20-20
- Min. limit output, 10.20-20
- Offset inverse characteristic, 10.20-20
- Output inversion, 10.20-21
- Switch-off, 10.10-7
- Unhide time, 10.20-20
Process controller , Stop, 10.10-7
Process controller setpoint
- Acceleration time, 10.20-20
- Deceleration time, 10.20-20
Process data output words, Free configuration,
10.13-12
Process variable, Calibration of application I/O,
10.16-3, 10.20-44
Protection measures, 4.2-2
Protection of persons, 3.4-1, 6.2-1
- with (earth-leakage cicuit-breaker (e.l.c.bs), 6.2-4
PTC motor monitoring, 10.14-3
Public mains, EN 61000-3-2, 6.2-3
Q
Quick stop, 10.7-4
R
Rated data
- Operation at rated power, 4.3-1
Rated data 230 V, 4.3-1
Rated data 400 V, 4.3-5
Rated data 500 V, 4.3-10
- Operation with increased rated power, 4.4-1
Rated data 230 V, 4.4-1
Rated data 400 V, 4.4-4
Rated data 500 V, 4.4-9
Rating, Brake resistors, 13.4-9
Ratings, Integrated brake transistor, 13.4-1
Reaction times of digital inputs, 10.13-1
Relay output
- Configuration, 10.13-6
- Connection, 6.4-7, 6.5-7
Reluctance motors, 1.4-1
Remote parameter setting
- Keypad EMZ9371BC, 9.4-9
- with E82ZBC keypad, 9.3-10
Reset, Error message, 11.5-1
Residual hazards, 3.4-1
Response in the event of communication errors,
10.20-14
Running optimisation, 10.4-1
S
S-shaped ramps, Smooth acceleration/deceleration,
10.7-1
Safe standstill, 14.1
Safety information, 3.1-1
Saving parameter sets, , 10.17-1
Selection, Operating mode, 8.3-1, 10.3-1
Sensor compensation
- Acceleration time, 10.20-19
- Deceleration time, 10.20-19
- Max. activation threshold, 10.20-19
- Min. activation threshold, 10.20-19
- Output signal, 10.16-2, 10.20-19
- Reset, 10.20-19
Sequential circuit, 15.7-1
Setpoint changeover, 10.8-17
Setpoint selection, 10.8-1, 10.20-15
- Bipolar, 10.8-6
- Field, 8.6-5, 10.8-3, 10.20-9
- Inverse, 10.8-7
- Normalisation, 10.20-16
- PID controller, 10.10-5
- Selection, 10.20-15
- unipolar, 10.8-6
- via bus systems, 10.8-16
- via fixed setpoint (JOG), 10.8-13
- via motor potentiometer, 10.8-11
- with keypad, 10.8-15
Setpoint selection range
- Application I/O, 8.6-5, 10.8-3, 10.20-9
- Standard I/O, 8.6-5, 10.8-3, 10.20-9
Setpoint source, Select, 10.8-1
Setpoint source selection, 10.8-1
Setpoint summation, 15.8-1
Setting range, 8.6-4, 10.6-1, 10.20-7
Show/Hide Bookmarks