What to do if Lexmark MX717 All in One Printer says 'Unsupported disk'?
If your Lexmark All in One Printer displays 'Unsupported disk', remove the unsupported printer hard disk, and then insert a supported one.
What to do if Lexmark MX717 All in One Printer shows 'Memory full'?
If your Lexmark All in One Printer displays a 'Memory full' message, you can try the following: * Touch 'Cancel job' on the printer control panel to clear the message. * Install additional printer memory.
What to do if Lexmark MX717 says 'Cartridge nearly low'?
If your Lexmark All in One Printer shows 'Cartridge nearly low', you can touch 'Continue' on the printer control panel to clear the message and continue printing, if necessary.
How to resolve 'Install Tray [x]' message on Lexmark MX717?
If your Lexmark All in One Printer displays 'Install Tray [x]', try the following: * Install the specified tray: 1. Turn off the printer. 2. Unplug the power cord from the electrical outlet. 3. Install the specified tray. 4. Connect the power cord to a properly grounded electrical outlet. 5. Turn the printer back on. * Cancel the print job. * Reset the active bin.
How to fix 'Network [x] software error' on Lexmark MX717?
Try one or more of the following: * From the printer control panel, touch Continue to continue printing. * Turn off the printer, wait for about 10 seconds, and then turn the printer back on.
What to do if Lexmark MX717 All in One Printer says 'Close door or insert cartridge'?
If your Lexmark All in One Printer shows 'Close door or insert cartridge', it means the toner cartridge is either missing or not correctly installed. You should insert the cartridge and ensure that all doors and covers are properly closed.
What to do when Lexmark MX717 says 'Replace imaging unit, 0 estimated pages remain'?
If your Lexmark All in One Printer displays 'Replace imaging unit, 0 estimated pages remain', replace the imaging unit to clear the message and continue printing.
Why is fax disabled on my Lexmark All in One Printer?
To enable faxing on your Lexmark All in One Printer, connect the printer to an analog phone line.
What to do if Lexmark MX717 All in One Printer says 'Too many trays attached'?
If your Lexmark All in One Printer displays 'Too many trays attached', follow these steps: 1. Turn off the printer. 2. Unplug the power cord from the electrical outlet. 3. Remove the extra trays. 4. Connect the power cord to a properly grounded electrical outlet. 5. Turn the printer back on.
How to fix 'Fax memory full' error on Lexmark MX717 All in One Printer?
If your Lexmark All in One Printer's fax memory is full, follow these steps: 1. From the control panel, touch 'Continue' to clear the message and cancel the fax job. 2. Reduce the fax resolution or the number of pages. 3. Send the fax job again.
General| Print Technology | Laser |
|---|---|
| Functionality | Print, Copy, Scan, Fax |
| Print Speed (Color) | 50 ppm |
| Print Resolution | 1200 x 1200 dpi |
| Monthly Duty Cycle | Up to 300, 000 pages |
| Processor Speed | 1.2 GHz |
| Connectivity | USB, Ethernet, Wi-Fi |
| Operating System Compatibility | Windows, macOS, Linux |
| Copy Speed (Color) | 50 cpm |
| Copy Resolution | 600 x 600 dpi |
| Fax Speed | 33.6 Kbps |
| Scan Resolution | 600 x 600 dpi |
| Standard Paper Capacity | 650 sheets |
| Paper Capacity (Maximum) | 3, 300 pages |
| Memory (Maximum) | 2 GB |
| Copy Reduce / Enlarge Range | 25% to 400% |
| Fax Transmission Speed | Approx. 3 seconds per page |
| Scan Technology | CIS |
| Mobile Printing | AirPrint, Google Cloud Print |
To Next Page
