41
206-4342
Installer Menu (Cont.)
014 - STRT CH IN SM (Start Channel in Scan Mode)
Only valid when item 013 SCAN MODE is set to 1 (enabled). Set
to 1 to force the Channel Map pivot point to be between the RF
channel designated as the Start Channel (see item 004 STRT
CHANNEL) and next lower channel in the Channel Map. Set to 0
(default) to disable.
Note: This item is not available in the Installer Menu when item
013 SCAN MODE is set to 0.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature is enabled and available to the
end user. Set to 0 to disable the Sleep Timer feature.
016 - EN. TIMER (Enable On/Off Timers)
If set to 1, the Timer function is enabled and available to the end
user. Set to 0 to disable On/Off timers.
Note: The TV clock must be set in order for timers to be used.
017 - ALARM
If set to 1, the Alarm feature is enabled and available to the end
user in the Function Menu (i.e., the TV is not in Pass-through
Mode). Set to 0 to disable the Alarm feature.
Note: The TV clock must be set before the Alarm feature will
work.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on “bed
number” in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Note: When item 027 HOSPITAL MODE is set to 0, both the
IR code that will control the TV and the speaker selection are
determined by this item (default = 1). Set this item as required to
enable Zenith Bed 1 or Bed 2 IR codes and Speaker selections.
Values IR Mode Bed # Speaker
0 – 1 Zenith (Hospital) 1 – 2 TV Only
16 – 24 Multi-code Remote 1 – 9 TV Only
64 – 65 Zenith (Hospital) 1 – 2 Pillow Only
Note: See Reference section, “LG Pro:Centric Patient Remote
and Pillow Speaker,” for additional information. Also, see
documentation for the accessory package that includes the multi-
code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to lter and control or otherwise restrict programming
content that can appear. Set to 0 to turn off the V-Chip feature (not
available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum number of Parental
Control blocking hours that can be set in the Function Menu (i.e.,
the TV is not in Pass-through Mode). Default setting is for 12
blocking hours.
Note: This item is not available in the Installer Menu when item 021
V-CHIP is set to 0 or when item 084 PERMANENT BLK is set to 1.
023 - CAPTION LOCK
If set to 0, captions are off when the TV is turned ON. If set to 1,
the caption setting selected before the TV was turned OFF will be
the current caption setting when the TV is turned ON again.
025 - FUNCTION PRE (Function Preview)
Set to 1 to allow access to the Channel Preview/Banks Setup
Menu via the CH PREVIEW key on Installer Remote. Set to 0 to
disable access to the Channel Preview/Banks Setup Menu.
Note: This item is only applicable when the TV is in PTC-CTV
Mode.
027 - HOSPITAL MODE
Set according to the speaker selection, the pillow speaker code/
supply voltage and the hospital IR code. If using a Pro:Centric
pillow speaker, select one of the Zenith codes in accordance with
the desired speaker selection. See table below.
When Hospital Mode is set to 0 (disabled), both the IR code
that will control the TV and the speaker selection depend on the
Installer Menu item 020 FEATURE LEVEL setting.
Value Speaker
Pillow Speaker
Code/Voltage
Hospital IR Code
000 Determined by
item 020 setting
Zenith (+12v) Determined by
item 020 setting
001 Pillow Only Zenith (+12v) Zenith Bed #1
002 Pillow Only Zenith (+12v) Zenith Bed #2
017 Pillow Only Philips (+5v) Zenith Bed #1
018 Pillow Only Philips (+5v) Zenith Bed #2
033 Pillow Only RCA (-5v) Zenith Bed #1
034 Pillow Only RCA (-5v) Zenith Bed #2
065 TV Only Zenith (+12v) Zenith Bed #1
066 TV Only Zenith (+12v) Zenith Bed #2
081 TV Only Philips (+5v) Zenith Bed #1
082 TV Only Philips (+5v) Zenith Bed #2
097 TV Only RCA (-5v) Zenith Bed #1
098 TV Only RCA (-5v) Zenith Bed #2
129 Both Pillow & TV Zenith (+12v) Zenith Bed #1
130 Both Pillow & TV Zenith (+12v) Zenith Bed #2
145 Both Pillow & TV Philips (+5v) Zenith Bed #1
146 Both Pillow & TV Philips (+5v) Zenith Bed #2
161 Both Pillow & TV RCA (-5v) Zenith Bed #1
162 Both Pillow & TV RCA (-5v) Zenith Bed #2
254 TV Only Disabled (0v) Zenith Bed #2
To Next Page
Loading...
