Why is my Liebert UPStation GXT 2U beeping and the battery indicator LED is on?
The Liebert UPS is operating from battery mode. This can occur because the UPS is not securely plugged into the wall socket, or the mains voltage is out of the UPS input range. Ensure the UPS is securely plugged into the wall socket and that the utility supply voltage is within acceptable limits for the UPS. Consider saving data and closing applications.
What to do if the battery indicator LED is illuminated on my Liebert UPStation GXT 2U UPS?
If the battery indicator LED is illuminated on your Liebert UPS, it means the UPS is operating from battery mode. First, make sure the UPS is securely plugged into the wall receptacle. If it is, the UPS input protection fuse may have blown. In this case, save your data, close applications, replace the UPS input fuse, and then restart the UPS. Another possibility is that the mains voltage is out of the UPS input range. Save your data, close applications, and ensure the mains supply voltage is within acceptable limits for the UPS.
What does it mean when the fault and bypass indicator LEDs and diagnostic LED C and E are illuminated on my Liebert UPS?
Your Liebert UPS has received a signal or command from the attached computer causing it to shut down. If this was inadvertent, ensure the communication cable used is correct for your system.
What to do if the fault and bypass indicator LEDs and diagnostic LED A are illuminated on my Liebert UPStation GXT 2U UPS?
This indicates that the Liebert UPS internal fan has a problem or the UPS shutdown due to a temperature condition, and the load is on bypass power. Ensure the UPS is not overloaded, that the ventilation openings are not blocked, and that the room ambient temperature is not excessive. Wait 30 minutes to allow the UPS to cool, then restart the UPS.
How to fix Liebert UPStation GXT 2U when it fails to start?
If your Liebert UPS fails to start, it may be short-circuited or overloaded. Turn the UPS off, disconnect all loads, and ensure nothing is lodged in the output sockets. Confirm that the loads are not defective or shorted internally.
What does it mean when the fault and bypass indicator LEDs and all load level LEDs are illuminated on my Liebert UPS?
This indicates that the Liebert UPS is overloaded or the connected load equipment is faulty. Check the load level display and remove non-essential loads. Recalculate the load VA and reduce the number of loads connected to the UPS. Also, check the connected equipment for faults.
Why does my Liebert UPStation GXT 2U have reduced battery time?
If the Liebert UPS has reduced battery time, it could be due to several reasons. First, the batteries may not be fully charged. To resolve this, keep the UPS plugged in continuously for at least 24 hours to recharge the batteries. Second, the UPS might be overloaded, so check the load level display and reduce the load on the UPS. Finally, the batteries may not be able to hold a full charge due to age, in which case you should replace them.
What does it mean when the battery LED is flashing on my Liebert UPStation GXT 2U UPS?
If the battery LED is flashing on your Liebert UPS and there is a continuous horn, it means the battery source is not available. Check the battery connections, completely power down, and then restart the UPS. Note that if the battery circuit opens while the UPS is running, it will be detected when the next battery test is performed.
What to do if my Liebert UPStation GXT 2U has reduced battery time?
Reduced battery time in your Liebert UPS can be due to several reasons: * **Batteries are not fully charged:** Keep the UPS plugged in continuously for at least 24 hours to recharge the batteries. * **UPS is overloaded:** Check the load level display and reduce the load on the UPS. * **Old batteries:** Batteries may not be able to hold a full charge due to age.
General| Product Type | UPS |
|---|---|
| Form Factor | 2U Rackmount |
| Frequency | 50/60 Hz |
| Input Voltage | 208V, 220V, 230V, 240V |
| Output Voltage | 208V, 220V, 230V, 240V |
| Battery Type | Sealed Lead Acid |
| Runtime | Varies by load and battery configuration |
| Communication Ports | USB |
| Operating Temperature | 0° to 40°C (32° to 104°F) |
| Operating Humidity | 0 to 95% non-condensing |
Contains important safety instructions for UPS operation.
Provides surge and interference protection for sensitive equipment.
Converts AC to DC power and shapes input current for efficiency.
Converts DC power to clean, regulated AC output power.
Maintains battery charge by regulating mains power.
Adjusts battery voltage for optimal inverter operation.
Describes the type and expected lifespan of the UPS batteries.
Provides an alternative path for mains power in case of UPS malfunction.
Instructions for setting up the UPS in a vertical tower configuration.
Instructions for mounting the UPS in a standard equipment rack.
Details the process of installing optional rack slide hardware.
Describes the functions of the ON/Alarm Silence/Manual Battery Test button.
Details the functions of the OFF and Manual Bypass button.
Details the Load/Battery Level, Fault, Bypass, UPS ON, and Battery indicator LEDs.
Explains the AC Input LED status and how to configure output voltage.
Describes the UPS operation when connected to mains power.
Explains UPS behavior during power outages or voltage issues.
Details the battery recharging process after mains power is restored.
Explains the UPS communication interface port and its pin assignments.
Covers remote shutdown features and advanced communication via Intellislot.
Details available option cards for enhanced UPS communication and control.
Provides an overview and safety precautions for battery replacement.
Step-by-step guide for replacing the UPS internal battery pack.
Information about Liebert Corporation's history and product offerings.
To Next Page
