Linkam Scientific Instruments CSS450 - Page 34

44 pages

To Next Page

To Previous Page

When the motor stops the there sensors will all be

set up and referenced. Ready for sample loading

in the next shearing run.

Click ‘OK’ and then click ‘X’ in the top corner to

close the window.

Main Page

Table of Contents2
Safety Information4
- Important Notice4
- Requirements for Safe Use4
- Caution Labels and Indicators4
- Handling Liquid Nitrogen5
- Filling the Dewar5
- Equipment Maintenance5
Informations de Sécurité5
- Note Importante5
- Exigences en Matière de Sécurité D'utilisation5
- Étiquettes D'avertissement Et Indicateurs6
- Manipulation de L'azote Liquid6
- Remplissage du Vase Dewar6
- Entretien de L'appareil6
Introduction7
Before Using Your Equipment7
Warranty7
Technical Support7
Feedback7
Equipment Operation7
Introduction to CSS450 Stage8
Anatomy of a CSS4509
Accessories10
Getting Started11
- Installing Linksys32 on a PC11
- Stand Assembly11
- Assembling the Lid and Base12
- Connecting the Lemo Cable12
Mounting on to a Microscope13
- Mounting on to a Dovetail13
- Set up Kohler Illumination13
Introduction to CSS450 System Controller14
- Back Panel Cable Connections14
- Stage Connector14
- Instrument Bus14
- Expansion Boards14
- External Input and Output Sockets14
- USB Connector14
- RS232 Connector14
- Linkpad Connector14
LNP95 Liquid Nitrogen Pump15
- Introduction15
- Remove Transit Screws15
Connecting the Stage to the Controller16
- Mains Connection16
Connecting the Water Cooling Supply/Circulator17
Connecting the Liquid Nitrogen Pump for Cryo-CSS450 System18
- Connecting the LNP9518
Setting up the Linksys32 Software20
- Changing the Comm Port Number21
Using Linksys32 Software21
- Linksys32 Tool Bar22
- CSS450 Tool Bar22
- CSS Status Window22
- Sensor Indicators22
- Jog Controls (Manual Mode)22
Loading the Sample23
Start the Shearing Experiment24
- Using the Shear Motor Profile24
- Start the Profile26
- Adjusting the Shear Parameters26
- General Setup26
- Velocities26
Finish a Shearing Experiment27
Maintenance Procedures28
- Changing the Windows28
- External Window Replacement28
- Base Window Replacement28
- Lid Window Replacement29
Setting the Sensors - Zero, Lid and Reference30
- Manually Setting the Windows to Zero Point30
Using the CSS-450 Gas Purge and Vertical Seal Stage35
- Using the Purge Ports35
- Base Window Replacement35
Troubleshooting36
- Unable to Set a Gap, Lid Seems Stuck36
- Comm Port Message36
- Motor Doesn't Start36
- Lid Can Rock Slightly When the Lid Nuts Are off37
Cooling Fault Diagnosis37
- Temperature Appears to be Several Degrees below the Displayed Temperature37
- The Cooling Rate Is Less than Specified37
Appendix 1 : Shear and Strain Explanation38
- Shear Control38
- Shear Rate38
- Strain (Shear) Value38
- Observation Radius38
Appendix 2 : Spare Parts List39
Appendix 3 : Declaration of Conformity40
Appendix 4 : Technical Specification41
- CSS450 Stage Technical Specification41
- CSS450 Controller Technical Specification41
- CSS450 Controller Equipment Ratings41
- RS232 Computer Interface41
- USB Interface41
- External Input and Output Sockets41
- CSS450 Motor Board42
- Optional Linkpad42
- Linkpad Equipment Ratings42
- LNP95 Liquid Nitrogen Pump42
- LNP95 Equipment Ratings42
Contact Information44

Linkam Scientific Instruments CSS450 - Page 34

Table of Contents

Related product manuals