What to do if Lippert Components Smart Jack Lifting Systems show ERROR Low Voltage?
If your Lippert Components Lifting Systems display an 'ERROR Low Voltage' message, it means the battery voltage has dropped below 10.8V. Check the wiring for loose connections. Also, test the battery voltage under load and charge or replace the battery if necessary.
Why does my Lippert Components Smart Jack Lifting Systems show ERROR Auto Level Fail?
The 'ERROR Auto Level Fail' message on your Lippert Components Lifting Systems indicates that the system is unable to auto-level. This can occur due to uneven ground, so check the disposition of the jacks and consider relocating the coach. It can also happen if the zero point was set incorrectly, so try resetting the zero point.
What to do if Lippert Components Smart Jack Lifting Systems show ERROR Feature Disabled?
The 'ERROR Feature Disabled' message on your Lippert Components Lifting Systems can occur for several reasons. If you're trying to initiate Hitch Recognition, ensure the front of the coach is above level and restart the Auto Level process. Another cause may be that the touch pad power wasn't cycled between leveling operations; turn the touch pad off and then back on to reset the system. Finally, this error can appear if the zero point hasn't been set, so set the zero point.
Why does my Lippert Components Lifting Systems show ERROR Excess Angle?
The 'ERROR Excess Angle' message on your Lippert Components Lifting Systems means that an excessive angle was reached during auto operation. This can happen if the controller is not properly secured, so check and secure the controller placement. It can also occur if the angle is too extreme for the system, so relocate the coach.
What to do if Lippert Components Smart Jack show ERROR Out Of Stroke?
If your Lippert Components Lifting Systems displays an 'ERROR Out Of Stroke' message, it means the jack has reached its maximum stroke length and is unable to lift further. Check the disposition of the jacks and relocate the coach.
How to troubleshoot ERROR LF Jack RF Jack LM Jack RM Jack LR Jack RR Jack on Lippert Components Lifting Systems?
If you are receiving an error for specific jacks on your Lippert Components Lifting Systems, check the harness connections at the controller and at the jack. Inspect the jack and harness for any damage, and repair or replace components as necessary. This error may also be caused by an unexpected high amp current stall.
What does ERROR External Sensor mean on Lippert Components Smart Jack Lifting Systems?
The 'ERROR External Sensor' message on your Lippert Components Lifting Systems indicates a bad connection or wiring issue from the controller to the rear sensor. Replace or repair the connection to the rear remote sensor.
What to do if PANIC STOP Function Aborted on Lippert Components Smart Jack?
If the 'PANIC STOP Function Aborted' message appears on your Lippert Components Lifting Systems, it means a button was pressed on the touch pad during an automatic operation. Restart the automatic operation and refrain from pressing any buttons on the touch pad.
Explains how to manually extend and retract landing gear and rear jacks.
Provides step-by-step instructions for unhitching the trailer from the tow vehicle.
Guides on how to properly reconnect the trailer to the tow vehicle.
Explains safety guidelines and system overview for Ground Control 3.0 (5th Wheel).
Step-by-step guide for safely unhitching the trailer from the tow vehicle.
Instructions for operating the OneControl touch panel.
Lists error codes for Rev. A touch panel/app and their solutions.
Lists error codes for Rev. B touch panel/app and their solutions.
Steps to unhitch the travel trailer using the TT system.
Process for initiating the automatic leveling sequence on the TT system.
Procedure for reconnecting the TT to the tow vehicle.
Instructions for using the auto leveling control touch pad.
Instructions for operating the myRV OneControl Touch Panel.
Process for hitch recognition with the myRV touch panel.
Step-by-step guide to setting the zero point for auto-leveling.
Instructions for operating the OneControl App.
Manual jack operation using the Linc Remote.
Procedure for automatic leveling.
Troubleshooting steps for the power unit of the system.
Procedure for manually operating stabilizers with the wrench.
Procedure for manually operating tongue jacks with the wrench.
Critical safety warnings and precautions for the Class C Hydraulic Leveling System.
Steps to perform the automatic leveling process.
Step-by-step guide for manually leveling the coach.
Manual steps to unhitch the trailer.
Safety precautions for installing and operating the Smart Jack.
Instructions for powered operation of the Smart Jack.
Steps for unhitching the trailer using the Smart Jack.
Steps for hitching the trailer using the Smart Jack.
Conditions and checks before operating the landing gear system.
A guide to diagnosing and correcting common problems.
Steps for unhitching the 5th Wheel.
Details the automatic leveling sequence for the 5th Wheel.
Process for hitch recognition when connecting to the 5th Wheel.
Procedure to reset the zero point for the 5th Wheel system.
Interprets error messages displayed on the LCD screen.
Steps for extending the X-Trek stabilizers.
Steps for retracting the X-Trek stabilizers.
Troubleshooting common issues with the X-Trek system.
Safety precautions for installing or operating the stabilizer.
Operational procedures for the Swing Down Stabilizer.
General| Power Source | 12V DC |
|---|---|
| Material | Steel |
| Type | Electric |
| Features | LED light |
| Motor Type | Electric |
To Next Page