What to do if Lippert Components Lifting Systems show ERROR Low Voltage?
If your Lippert Components Lifting Systems display an 'ERROR Low Voltage' message, it means the battery voltage has dropped below 10.8V. Check the wiring for loose connections. Also, test the battery voltage under load and charge or replace the battery if necessary.
Why does my Lippert Components Lifting Systems show ERROR Auto Level Fail?
The 'ERROR Auto Level Fail' message on your Lippert Components Lifting Systems indicates that the system is unable to auto-level. This can occur due to uneven ground, so check the disposition of the jacks and consider relocating the coach. It can also happen if the zero point was set incorrectly, so try resetting the zero point.
What to do if Lippert Components Lifting Systems show ERROR Feature Disabled?
The 'ERROR Feature Disabled' message on your Lippert Components Lifting Systems can occur for several reasons. If you're trying to initiate Hitch Recognition, ensure the front of the coach is above level and restart the Auto Level process. Another cause may be that the touch pad power wasn't cycled between leveling operations; turn the touch pad off and then back on to reset the system. Finally, this error can appear if the zero point hasn't been set, so set the zero point.
Why does my Lippert Components PSX1 Lifting Systems show ERROR Excess Angle?
The 'ERROR Excess Angle' message on your Lippert Components Lifting Systems means that an excessive angle was reached during auto operation. This can happen if the controller is not properly secured, so check and secure the controller placement. It can also occur if the angle is too extreme for the system, so relocate the coach.
What to do if Lippert Components PSX1 show ERROR Out Of Stroke?
If your Lippert Components Lifting Systems displays an 'ERROR Out Of Stroke' message, it means the jack has reached its maximum stroke length and is unable to lift further. Check the disposition of the jacks and relocate the coach.
How to troubleshoot ERROR LF Jack RF Jack LM Jack RM Jack LR Jack RR Jack on Lippert Components Lifting Systems?
If you are receiving an error for specific jacks on your Lippert Components Lifting Systems, check the harness connections at the controller and at the jack. Inspect the jack and harness for any damage, and repair or replace components as necessary. This error may also be caused by an unexpected high amp current stall.
What does ERROR External Sensor mean on Lippert Components PSX1 Lifting Systems?
The 'ERROR External Sensor' message on your Lippert Components Lifting Systems indicates a bad connection or wiring issue from the controller to the rear sensor. Replace or repair the connection to the rear remote sensor.
What to do if PANIC STOP Function Aborted on Lippert Components PSX1 Lifting Systems?
If the 'PANIC STOP Function Aborted' message appears on your Lippert Components Lifting Systems, it means a button was pressed on the touch pad during an automatic operation. Restart the automatic operation and refrain from pressing any buttons on the touch pad.
General system overview and essential safety precautions.
Pre-operation checks and conditions for safe system use.
Covers basic jack controls, dropping off unit, and vehicle reconnection.
Procedures for zero point calibration and resolving system errors.
Routine maintenance tasks for system longevity.
Overview and safety guidelines specific to the 5th Wheel system.
Visual guide to the touch pad and fundamental jack operations.
Detailed steps for auto leveling and hitch recognition sequences.
Guidance for diagnosing system issues and interpreting error messages.
Information on the touch panel, app, and remote control system.
Instructions for unhitching, auto leveling, and hitch recognition via touch panel.
Procedures for using the mobile app and optional remote control.
Information on LED indicators, error codes, and troubleshooting steps.
Overview of the TT leveling system and essential safety precautions.
Diagram of the touch pad and basic operational procedures.
Steps for auto-leveling and reconnecting to the tow vehicle.
Guidance for system issues and manual override methods.
Overview of the PSX1 system and critical safety warnings.
Instructions for extending and retracting stabilizer legs.
Procedures for manual operation and system upkeep.
Overview of the PSX2 system and critical safety warnings.
Procedures for extending and retracting stabilizer legs.
Steps for manual operation and ongoing system maintenance.
Information on the 3-in-1 override handle and safety precautions.
Instructions for manual operation of stabilizers and tongue jacks.
Overview of the hydraulic system and safety guidelines.
Guidelines for operating the system and selecting a suitable site.
Steps for zero point calibration and manual leveling.
Common errors, user alarms, and system maintenance tasks.
Details about the power tongue jack and its safety aspects.
Procedures for operating the jack and connecting/disconnecting the trailer.
Steps for manual use and common troubleshooting tips.
Overview of the Smart Jack and its safety requirements.
Instructions for powered operation, hitch height memory, and auto retract.
Steps for manually operating the Smart Jack for unhitching/hitching.
Overview of the landing gear system and operational guidelines.
Instructions for extending and retracting landing gear.
Common issues and their solutions for the landing gear system.
Overview of Patriot Jack Systems and basic operation.
Maintenance schedules and fluid recommendations for hydraulic systems.
Common problems and their corrective actions for the system.
Overview of the Level Up system and its key features.
Details of system components and critical safety warnings.
Instructions for operating the system and auto-leveling.
Procedures for calibration and manual system control.
Guidance on error codes, maintenance, and fluid recommendations.
Overview of the X-Trek system and safety precautions.
Instructions for extending and retracting stabilizers.
Guidance on loss of air pressure, line breaks, and system purge.
Overview of the swing down stabilizer and safety guidelines.
Instructions for extending and retracting the stabilizer legs.
General| Voltage | 12V DC |
|---|---|
| Stroke Length | 18 inches |
| Control | Remote Control |
| Installation | Bolt-on |
| Application | Leveling and stabilizing RVs |
| Lift Type | Electric |
| Type | Electric Stabilizing Jack System |
| Compatibility | Travel Trailers, Fifth Wheels |
To Next Page
