EasyManua.ls Logo

Lippert Components Happijac - User Manual

Lippert Components Happijac
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Happijac
®
Bed Lift
OWNER'S MANUAL

Table of Contents

Other manuals for Lippert Components Happijac

Preview: Oem Installation Manual
Oem Installation Manual22 pages
Preview: Installation Manual
Installation Manual14 pages
Preview: Manual
Manual6 pages

Questions and Answers

  • S
    Susan BirdJul 31, 2025
    What to do if Lippert Components Industrial Equipment bed(s) will not move either up or down when switch is pressed?
    • L
      Luis TaylorAug 1, 2025
      If your Lippert Components Industrial Equipment bed(s) won't move up or down when you press the switch, it could be due to several reasons. First, ensure your trailer batteries are adequately charged or connect to shore power or a generator. If power isn't the issue, the control module or the UP/DOWN switch might be faulty and need replacement. If these steps don't resolve the problem, the motor may be defective, and you should contact LCI Customer Service.
  • H
    Henry CunninghamAug 5, 2025
    Why Lippert Components Industrial Equipment bed lowers, but stops part way going up?
    • M
      michael52Aug 5, 2025
      If your Lippert Components Industrial Equipment bed lowers, but stops part way going up, it could be due to insufficient power. Make sure your trailer batteries are adequately charged, or connect to shore power or a generator. Alternatively, the motor/brake assembly may be defective; in this case, contact LCI Customer Service.
  • T
    Teresa SchneiderAug 9, 2025
    What to do if Lippert Components Industrial Equipment bed travels in only one direction?
    • S
      sarah82Aug 10, 2025
      If your Lippert Components Industrial Equipment bed only travels in one direction, it could be caused by a defective limit switch, a faulty control module, or a faulty UP/DOWN switch. Try replacing the switch or module. Another potential cause is a faulty brake. Set the manual brake release lever on the motor to the "OFF" position. If the bed(s) then move, replace the faulty brake.
  • V
    vsmithAug 13, 2025
    What to do if Lippert Components Industrial Equipment bed fails to stop at preset stop point when lowered?
    • R
      roberthaleAug 13, 2025
      If your Lippert Components Industrial Equipment bed fails to stop at the preset stop point when lowered, the motor brake might not be engaging, or the limit switch may be defective. Contact LCI Customer Service regarding the motor brake, or replace the switch.
  • P
    Patricia DaughertyAug 17, 2025
    What to do if Lippert Components Industrial Equipment bed fails to stop at preset stop point when raised?
    • M
      Mike MccoyAug 17, 2025
      If your Lippert Components Industrial Equipment bed fails to stop at the preset stop point when raised, the limit switch may be defective or damaged. Replace the switch to resolve this issue.
  • C
    conradmelissaAug 22, 2025
    Why Lippert Components Industrial Equipment bed does not stay level side-to-side or front-to-back?
    • T
      Tracy MooreAug 22, 2025
      If your Lippert Components Industrial Equipment bed does not stay level (side-to-side or front-to-back), it could be due to a broken or loose timing shaft, or a broken chain sprocket. In either case, contact LCI Customer Service.
  • M
    Michael MurphyAug 27, 2025
    How to fix if upper bunk (two- bed system) of Lippert Components Industrial Equipment does not lower smoothly?
    • A
      Andrea RoyAug 27, 2025
      If the upper bunk in your Lippert Components Industrial Equipment two-bed system does not lower smoothly, the bed carrier might be sticky. Try spraying a small amount of dry silicone lubricant into the rails.

Summary

Safety Information

Safety Warnings and Cautions

Details safety risks associated with WARNING and CAUTION symbols and procedures.

Operating Precautions

General Operating Precautions

Lists essential safety checks and prohibitions during operation.

Operation

Control Switch Operation

Describes how to use the UP/DOWN control switch for the bed lift.

Upper Trolleys Lowering

Troubleshooting

Troubleshooting Common Issues

Lists common problems, their causes, and recommended solutions.

Emergency Manual Operation

Manually Raising the Bed(s);Sofa or Dinettes

Procedure for manually raising the bed or sofa/dinette.

Manually Lowering the Bed(s)

Lippert Components Happijac Specifications

General IconGeneral
CategoryLifting Systems
ManufacturerLippert Components
BrandHappijac
Mounting TypeFrame-mounted
Lifting CapacityVaries by model
OperationElectric

Related product manuals