Lippert Components Ground Control 2.0

Other manuals for Lippert Components Ground Control 2.0

Owner's Manual12 pages

Stabilizer Instructions2 pages

Questions and Answers

T
Thomas HernandezAug 14, 2025
What to do if Lippert Components Laser Level shows error at specific jack?
- C
  Cassandra ZimmermanAug 14, 2025
  If your Lippert Components Laser Level shows an error at a specific jack (left front, right front, left rear, right rear), inspect the harness connections at both the controller and the jack. Also, check the jack and harness for any signs of damage. Repair or replace any damaged components as needed.
C
cbellAug 17, 2025
What to do if Lippert Components Ground Control 2.0 show ERROR Low Voltage?
- C
  Cameron HawkinsAug 18, 2025
  If your Lippert Components Lifting Systems display an 'ERROR Low Voltage' message, it means the battery voltage has dropped below 10.8V. Check the wiring for loose connections. Also, test the battery voltage under load and charge or replace the battery if necessary.
J
Jessica HopkinsAug 20, 2025
Why does my Lippert Components Lifting Systems show ERROR Auto Level Fail?
- S
  Stanley PatelAug 20, 2025
  The 'ERROR Auto Level Fail' message on your Lippert Components Lifting Systems indicates that the system is unable to auto-level. This can occur due to uneven ground, so check the disposition of the jacks and consider relocating the coach. It can also happen if the zero point was set incorrectly, so try resetting the zero point.
S
Sandra FuentesAug 25, 2025
What to do if Lippert Components Ground Control 2.0 show ERROR Feature Disabled?
- L
  lisachangAug 25, 2025
  The 'ERROR Feature Disabled' message on your Lippert Components Lifting Systems can occur for several reasons. If you're trying to initiate Hitch Recognition, ensure the front of the coach is above level and restart the Auto Level process. Another cause may be that the touch pad power wasn't cycled between leveling operations; turn the touch pad off and then back on to reset the system. Finally, this error can appear if the zero point hasn't been set, so set the zero point.
W
William JordanAug 27, 2025
Why does my Lippert Components Ground Control 2.0 show ERROR Excess Angle?
- S
  seanandrewsAug 27, 2025
  The 'ERROR Excess Angle' message on your Lippert Components Lifting Systems means that an excessive angle was reached during auto operation. This can happen if the controller is not properly secured, so check and secure the controller placement. It can also occur if the angle is too extreme for the system, so relocate the coach.
E
Erik LongAug 31, 2025
What to do if Lippert Components Lifting Systems show ERROR Out Of Stroke?
- S
  Stacy WashingtonAug 31, 2025
  If your Lippert Components Lifting Systems displays an 'ERROR Out Of Stroke' message, it means the jack has reached its maximum stroke length and is unable to lift further. Check the disposition of the jacks and relocate the coach.
G
Gary EvansSep 3, 2025
How to troubleshoot ERROR LF Jack RF Jack LM Jack RM Jack LR Jack RR Jack on Lippert Components Ground Control 2.0?
- J
  Julie PerezSep 3, 2025
  If you are receiving an error for specific jacks on your Lippert Components Lifting Systems, check the harness connections at the controller and at the jack. Inspect the jack and harness for any damage, and repair or replace components as necessary. This error may also be caused by an unexpected high amp current stall.
G
George OsborneSep 6, 2025
What does ERROR External Sensor mean on Lippert Components Lifting Systems?
- A
  Allison NunezSep 7, 2025
  The 'ERROR External Sensor' message on your Lippert Components Lifting Systems indicates a bad connection or wiring issue from the controller to the rear sensor. Replace or repair the connection to the rear remote sensor.
D
David AdamsSep 10, 2025
What to do if PANIC STOP Function Aborted on Lippert Components Lifting Systems?
- S
  sharon39Sep 10, 2025
  If the 'PANIC STOP Function Aborted' message appears on your Lippert Components Lifting Systems, it means a button was pressed on the touch pad during an automatic operation. Restart the automatic operation and refrain from pressing any buttons on the touch pad.