Lippert Components Happijac Installation Manual

14 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Happijac

®

Bed Lift

OEM INSTALLATION MANUAL

Other manuals for Lippert Components Happijac

Owner's Manual16 pages

Oem Installation Manual22 pages

Questions and Answers:

S
Susan BirdJul 31, 2025
What to do if Lippert Components Industrial Equipment bed(s) will not move either up or down when switch is pressed?
- L
  Luis TaylorAug 1, 2025
  If your Lippert Components Industrial Equipment bed(s) won't move up or down when you press the switch, it could be due to several reasons. First, ensure your trailer batteries are adequately charged or connect to shore power or a generator. If power isn't the issue, the control module or the UP/DOWN switch might be faulty and need replacement. If these steps don't resolve the problem, the motor may be defective, and you should contact LCI Customer Service.
H
Henry CunninghamAug 5, 2025
Why Lippert Components Industrial Equipment bed lowers, but stops part way going up?
- M
  michael52Aug 5, 2025
  If your Lippert Components Industrial Equipment bed lowers, but stops part way going up, it could be due to insufficient power. Make sure your trailer batteries are adequately charged, or connect to shore power or a generator. Alternatively, the motor/brake assembly may be defective; in this case, contact LCI Customer Service.
T
Teresa SchneiderAug 9, 2025
What to do if Lippert Components Industrial Equipment bed travels in only one direction?
- S
  sarah82Aug 10, 2025
  If your Lippert Components Industrial Equipment bed only travels in one direction, it could be caused by a defective limit switch, a faulty control module, or a faulty UP/DOWN switch. Try replacing the switch or module. Another potential cause is a faulty brake. Set the manual brake release lever on the motor to the "OFF" position. If the bed(s) then move, replace the faulty brake.
V
vsmithAug 13, 2025
What to do if Lippert Components Industrial Equipment bed fails to stop at preset stop point when lowered?
- R
  roberthaleAug 13, 2025
  If your Lippert Components Industrial Equipment bed fails to stop at the preset stop point when lowered, the motor brake might not be engaging, or the limit switch may be defective. Contact LCI Customer Service regarding the motor brake, or replace the switch.
P
Patricia DaughertyAug 17, 2025
What to do if Lippert Components Industrial Equipment bed fails to stop at preset stop point when raised?
- M
  Mike MccoyAug 17, 2025
  If your Lippert Components Industrial Equipment bed fails to stop at the preset stop point when raised, the limit switch may be defective or damaged. Replace the switch to resolve this issue.
C
conradmelissaAug 22, 2025
Why Lippert Components Industrial Equipment bed does not stay level side-to-side or front-to-back?
- T
  Tracy MooreAug 22, 2025
  If your Lippert Components Industrial Equipment bed does not stay level (side-to-side or front-to-back), it could be due to a broken or loose timing shaft, or a broken chain sprocket. In either case, contact LCI Customer Service.
M
Michael MurphyAug 27, 2025
How to fix if upper bunk (two- bed system) of Lippert Components Industrial Equipment does not lower smoothly?
- A
  Andrea RoyAug 27, 2025
  If the upper bunk in your Lippert Components Industrial Equipment two-bed system does not lower smoothly, the bed carrier might be sticky. Try spraying a small amount of dry silicone lubricant into the rails.

Lippert Components Happijac Specifications

General

Category	Lifting Systems
Manufacturer	Lippert Components
Brand	Happijac
Mounting Type	Frame-mounted
Lifting Capacity	Varies by model
Operation	Electric

Related product manuals

Project 2000 12600 Series

Preview: ground control 3.0

ground control 3.0

Preview: Lippert Components Level-Up

Lippert Components Level-Up

Preview: ground control TT

ground control TT

Lippert Components Power Gear

Preview: Lippert Components PSX1

Lippert Components PSX1

Ground Control 2.0

Lippert Components Bed Lift

Lippert Components PSX2

Lippert Components Smart Jack