EasyManua.ls Logo

LORCH MicorStick - User Manual

LORCH MicorStick
21 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
909.2049.9-00
EN
Operation Manual Page 17
MicorStick

Table of Contents

Questions and Answers

  • J
    Jacob RussellJul 26, 2025
    Why does the arc not ignite on my LORCH Welding System?
    • D
      Danielle BrownJul 26, 2025
      If the arc does not ignite on your LORCH Welding System, there might be several reasons. First, check for proper ground contact. Second, ensure that you are using the correct electrode diameter. Third, the welding current might be set too low, so increase it. Also, inspect the tungsten electrode for soiling or incorrect grinding; regrind or replace it if needed. Finally, verify that the gas volume is set correctly.
  • L
    Laurie BennettJul 31, 2025
    What to do if there is no welding current in LORCH MicorStick?
    • C
      Caitlin PierceJul 31, 2025
      If there is no welding current in your LORCH Welding System, the ground line might not be connected or could be defective; check and replace it if necessary. Additionally, the electrode holder or torch might be either disconnected or defective; inspect and replace them if needed.
  • S
    Sarah WhiteAug 4, 2025
    How to prevent pores in weld metal with LORCH MicorStick?
    • A
      Angel SanchezAug 4, 2025
      If you notice pores in the weld metal when using your LORCH Welding System, several factors could be responsible. Start by checking the torch and gas nozzle to ensure they are tight; tighten the gas nozzle if loose and replace the torch if necessary. Also, inspect the torch head for faults and replace it if needed. Ensure the workpiece is clean from grease, rust, oil, etc. Finally, consider whether there is a draught affecting the weld and shield the workplace if necessary.
  • M
    Mrs. Ashley HayesAug 8, 2025
    Why do the displays remain dark on my LORCH Welding System?
    • A
      Adam MeltonAug 8, 2025
      If the displays on your LORCH Welding System remain dark, it could be due to a defective mains fuse; replace it. Another possibility is a missing neutral conductor or mains phase; check the mains cable and any mains extension cables. Lastly, if the system uses a battery, it might be discharged; check, charge, or replace the battery.
  • S
    shelley47Aug 12, 2025
    What causes no inert gas in LORCH MicorStick?
    • Y
      yjonesAug 12, 2025
      If there is no inert gas flow in your LORCH Welding System, the gas cylinder may be empty; replace it. The pressure reducer could also be defective; check it and replace if necessary. Another potential issue is that the gas valve on the torch may not be opened or could be defective; check and replace it if necessary.
  • K
    kennedywesleyAug 17, 2025
    Why is there too little inert gas in my LORCH MicorStick Welding System?
    • H
      Hannah SandersAug 17, 2025
      If your LORCH Welding System is outputting too little inert gas, the torch might not be tight, so check and replace if necessary. Also, the gas hose might not be tight; tighten it. Lastly, the pressure reducer could be set incorrectly or be defective; check and replace if necessary.
  • J
    Jessica GoodmanAug 21, 2025
    Why is the TIG electrode melting on my LORCH Welding System?
    • D
      doylepatriciaAug 21, 2025
      If the TIG electrode is melting in your LORCH Welding System, it could be because the welding current is set too high for the electrode diameter; set the correct welding current. Alternatively, the polarity may be reversed with the TIG torch connected to the positive terminal; connect the TIG torch to the negative terminal.

Summary

Control Panel Overview

Control Panel Elements

Details on LEDs, buttons, and rotary knob for operation.

Machine Elements and Symbols

Machine Components

Lists and describes key parts like cables, sockets, and panel.

Symbol Interpretation

Explains manual and machine symbols and their meanings.

Safety Precautions

General Working Conditions

Guidelines for safe operation and preparation of the workspace.

Electrical Safety

Precautions related to electrical connections and components.

Ambient Conditions and Unit Protection

Operating Environment Requirements

Specifies temperature, humidity, and air quality for operation.

Overload Protection and Cooling

Details on overload protection, fan cooling, and ventilation guidelines.

Switch-on Duration (ED)

Explanation of duty cycle (ED) and thermal protection.

Setup and Operating Instructions

Setup and Transport Guidelines

Instructions for safe setup, placement, and transportation of the machine.

Initial Operating Steps

Step-by-step guide to connect cables and start welding.

Fastening the Transportation Belt

Instructions for attaching the transportation belt.

Connecting the Ground Cable

Guidelines for properly connecting the ground clamp.

Power Source Options and Welding Processes

Battery Operation

Using the machine with a MobilePower battery pack.

Generator Operation

Connecting the machine to a power generator.

Connecting the Electrode Cable

How to connect the electrode cable to the machine.

Installing Electrodes for TIG Welding

Step-by-step guide for installing electrodes in the TIG torch.

Control Panel and Commissioning

Control Panel Elements

Detailed explanation of LEDs, buttons, and rotary knob functions.

Energy-Saving Function

Details on the machine's energy-saving features for mains and battery operation.

Welding Process Details

System Activation and Arc Ignition

Steps for switching on and igniting the arc for electrode welding.

Hotstart and Current Settings

Explanation of hotstart function and current intensity guidance.

TIG Welding System Activation

Steps for switching on and igniting the arc for TIG welding.

Technical Data and Messages

Welding Specifications

Detailed technical parameters for welding operations.

Mains and Machine Specifications

Technical details regarding power supply, protection, and dimensions.

Fault Indicators and Rectifications

Lists common faults, causes, and recommended solutions.

Troubleshooting Guide

No Welding Current Issues

Solutions for problems related to no welding current.

Arc Ignition Problems

Troubleshooting steps for issues with arc ignition.

Inert Gas Issues

Solutions for problems concerning inert gas supply.

Weld Quality Issues

Addressing issues like pores and unsteady arcs.

Maintenance, Disposal, and Service

Related Accessories

Reference to figures showing available accessories.

Maintenance and Cleaning

Guidelines for routine maintenance and cleaning procedures.

Service and Contact

Contact details for technical service and support.

Declaration of Conformity

Statement of compliance with relevant EU directives and standards.

Spare Parts and Schematic

Validity and Part Numbers

Information on product validity and listing of part numbers.

Spare Parts List

Component Identification and Numbers

Detailed listing of parts with their numbers and descriptions.

LORCH MicorStick Specifications

General IconGeneral
BrandLORCH
ModelMicorStick
CategoryWelding System
LanguageEnglish

Related product manuals