24
(5) When the next time the enter button is pressed, the
changed BAL LINE-1 setting is determined, the level of
BAL-2 starts blinking and the level adjustment of BAL
LINE-2 becomes available. (Display on the 4th row of
Fig. 1Ⓑ)
When the enter button is pressed again, the display
goes to the level adjustment of BAL LINE-3.
(6) Pressing ▼ decreases the sound volume of BAL LINE-2
in steps of 0.5 dB. Adjustment is available in the range
between 0 and –6 dB.
Example) Pressing ▼ once displays –0.5 dB. (Display on
the 5th row of Fig. 1Ⓑ)
(7) When the next time the enter button is pressed, the
changed BAL LINE-2 setting is determined, the level of
BAL-3 starts blinking and the level adjustment of BAL
LINE-3 becomes available. (Display on the 6th row of
Fig. 1Ⓑ)
When the enter button is pressed again, the display
goes to the level adjustment of LINE-1.
(8) Pressing ▼ decreases the sound volume of BAL LINE-3
in steps of 0.5 dB. Adjustment is available in the range
between 0 and –6 dB.
Example) Pressing ▼ once displays –0.5 dB. (Display on
the 7th row of Fig. 1Ⓑ)
(9) When the next time the enter button is pressed, the
changed BAL LINE-3 setting is determined, the level of
LINE-1 starts blinking and the level adjustment of LINE-1
becomes available. (Display on the 8th row of Fig. 1Ⓑ)
When the enter button is pressed again, the display
goes to the level adjustment of LINE-2.
(10) Pressing ▼ decreases the sound volume of LINE-1 in
steps of 0.5 dB. Adjustment is available in the range
between 0 and –6 dB.
Example) Pressing ▼ once displays –0.5 dB. (Display
on the 9th row of Fig. 1Ⓑ)
(11) When the next time the enter button is pressed, the
changed LINE-1 setting is determined, the level of
LINE-2 starts blinking and the level adjustment of
LINE-2 becomes available. (Display on the 10th row of
Fig. 1Ⓑ)
When the enter button is pressed again, the display
goes to the level adjustment of LINE-3.
(12) Pressing ▼ decreases the sound volume of LINE-2 in
steps of 0.5 dB. Adjustment is available in the range
between 0 and –6 dB.
Example) Pressing ▼ once displays –0.5 dB. (Display
on the 11th row of Fig. 1Ⓑ)
(13) When the next time the enter button is pressed, the
changed LINE-2 setting is determined, the level of
LINE-3 starts blinking and the level adjustment of
LINE-3 becomes available. (Display on the 12th row of
Fig. 1Ⓑ)
When the enter button is pressed again, the display
goes back to the setting of (3) and the level adjustment
of BAL LINE-1 becomes available again.
(14) Pressing ▼ decreases the sound volume of LINE-3 in
steps of 0.5 dB. Adjustment is available in the range
between 0 and –6 dB.
Example) Pressing ▼ once displays –0.5 dB. (Display
on the 13th row of Fig. 1Ⓑ)
(15) When the next time the enter button is pressed, the
display goes back to the setting of (3) and the level
adjustment of BAL LINE-1 becomes available again.
When the preset button is pressed, the preset mode is
exited.
When the preset button is pressed, in any of the states
from (1) through (15), the setting is stored and the pre-
set mode is exited.
Or when no operation is performed for 1 minute in the
preset mode, this mode is exited while keeping the
state where the immediately preceding setting is stored
and the display returns to the normal display.
How to use Remote Control