Need help?Do you have a question about the Mackie DLM8 and is the answer not in the manual?
General| Product color | Black |
|---|---|
| Housing material | - |
| Recommended usage | DJ |
| Suitable for outdoor use | Yes |
| Magnet type | Ferrite |
| Speaker type | 2-way |
| Woofer diameter | 203 mm |
| Number of drivers | 1 |
| Speaker placement | Floor, Wall-mountable |
| Audio output channels | 2.0 channels |
| Driver diaphragm material | Paper |
| Woofer diameter (imperial) | 8 \ |
| Subwoofer driver diameter (imperial) | 1.75 \ |
| Amplifier class | D |
| Sensitivity | 125 dB |
| Frequency range | 65 - 20000 Hz |
| RMS rated power | 1000 W |
| Crossover frequency | 1600 Hz |
| Peak Music Power Output (PMPO) | 2000 W |
| Total Harmonic Distortion (THD) | 1 % |
| Voice coil diameter | 44 mm |
| Connectivity technology | Wired |
| AC input voltage | 220 - 240 V |
| Power source type | AC |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 250 W |
| Operating temperature (T-T) | 0 - 40 °C |
| Package depth | 409 mm |
| Package width | 419 mm |
| Package height | 406 mm |
| Package weight | 11800 g |
Weight and Dimensions| Depth | 302 mm |
|---|---|
| Width | 307 mm |
| Height | 313 mm |
| Weight | 10000 g |
Information on the proper disposal of the product according to WEEE Directive.
Example setup for a small club using DLM loudspeakers and subwoofer.
Example setup for a DJ using a laptop and DLM loudspeakers.
Explanation of how to connect multiple DLM loudspeakers using the THRU jack.
Example setup for a large club using Mackie DLM loudspeakers and subwoofers.
Details on connecting the AC power cord to the IEC receptacle.
Information on operating the rocker-style power switch.
Importance of not obstructing ventilation openings for cooling.
How to use the integrated kickstand for monitor use.
Describes the dual-purpose input connectors for mic and line signals.
How to set the switch for mic or line-level signals on Channel 1.
Details stereo RCA inputs for line-level sources like CD players or iPods.
Explains the male XLR output for daisy-chaining.
Selects signal (Ch 1 only or Mix) sent to the THRU output.
Describes the display for loudspeaker information and settings.
How to adjust level, EQ, and FX Send using buttons and parameter controls.
Explains the 3-band EQ (Low, Mid, High) for adjusting frequencies.
Option to set the front LED to On, Off, or Limit mode.
Access and control of system presets like EQ, Delay, FX, and Feedback Destroyer.
Using delay for alignment stacks and balcony fills, not as an effect.
Details the 16 "gig ready" effects available for system-wide use.
Explains the Feedback Destroyer modes: Off, On, Clear, and Hold.
How to save and recall system settings using the MEM button.
How to lock the DLM interface to prevent accidental changes.
Describes the function of the '+' and '-' buttons for adjustments.
Explains the switch to change the output power from 2000W to 2W.
How the built-in compressor protects against transient peaks.
High-pass filter to prevent low-frequency damage to the woofer.
How the amplifier module manages heat and protects against overheating.
Displays UI version, DSP version, Amp B+, and temperature.
Importance of correct voltage and sufficient amperage for AC power.
Provides solutions for common issues like no power, no sound, poor bass, etc.
Steps to diagnose and resolve power-related issues.
Steps to diagnose and resolve sound-related issues.
Explains potential causes for poor bass response.
Tips for addressing distortion and other sound quality problems.
How to identify and fix unwanted noise.
Solutions for hum problems, including ground loops.
Details the wiring and use of XLR input and output connectors.
Explains the stereo TRS connectors and their use with Hi-Z instruments.
Describes RCA connectors for line-level audio sources.
Comprehensive specs including acoustic performance, EQ, and frequency sections.
Details on system, low frequency, and high frequency power amplifier ratings.
Features of the DL2 mixer like EQ, delay, FX, and memory.
Lists impedance and type for all input and output connectors.
Specifies voltage and wattage for line input power.
Describes floor, pole, wall, and flying mounting options.
Details input protection and display LED functions.
Lists available mounting hardware and accessories.
Information on cabinet, finish, handles, grille, fly points, and monitor angle.
States the right to change specifications without notice.
Lists height, width, depth, and weight for DLM8 and DLM12.
Contact information and resources for support and help.
To Next Page
