SERVICE INFORMATION
Explanation Of Fault Codes Adjusting Oven Temperature
Yourapplianceisequipped withan electronic controlfeB- Your new appliance has been factory tested for oven
turing built-in, self-diagnostic software. This software temperature accuracy. Eventhough your oven has been
continuously monitors the control to insure safe and tested, you may find that the cooking results with your
proper operation. If the softwareshould detect a ques- new oven are different from your previous oven.
tionable situation, a FAULTCODE (Fplusa number) will
appear inthe display and continuous beepsmay sound. If you have carefully followed the recipe, reviewed the
bakingtips on page 8 and stillfeel cooking resultsdo not
If A Fault Code Appears meetyour expectations,youcanadjusttheoventemper-
A faultcode indicatesthattheremay be a functionaler- ature. DO NOT ADJUST THE TEMPERATURE if only
ror.As a safetyprecaution,thecontrolwillautomatically one ortwo itemsare notbaking properly.
cancel the program.Followinstructionsbelowto deter-
mineifserviceis required. Ifyouthinkthe ovenshouldbe hotterorcooler,youcan
adjust it yourself.Todecide how muchto change the
thermostat,settheoventemperature25°F higherortow-
During Normal Oven Cooking er than the temperaturein yourrecipe,then bake. The
If a fault codeappears in the displayand continuous resultsofthe"test"shouldgiveyouanideaof howmuch
beeps sound, press the STOP/CLEAR button.Then, to adjustthe thermostat.
reprogramthe cookingoperation.
NOTE: On doublewallovens,onlythe upperoventern-
Ifthe fault code reappearsinthe display,call an autho- peraturecanbe adjustedas describedbelow.
rizedservicer.Donotusethe oven untilthe controlhas
been serviced.
To adjust the thermostat:
During A Self-Clean Cycle 1. PressBAKETEMP button.
Iftheovenisheavilysoiled,excessivesmokeandflaring
mayresultinafaultcode.Ifthisoccurs,presstheSTOP/ 2. TurnSET knobuntil550° is displayed.
CLEAR buttonand allowthe oven to coolfor an hour.
Then, reprogramthe ovenforthe cleancycle. 3. Press and hold the BAKETEMP buttonfor several
secondsuntil00° appears in the display.
Ifthe faultcodereappearsinthe display,callan autho-
rizedservicer.De notusethe ovenuntilthe controlhas • If 00° does not appear in the display,press the
been serviced. STOP/CLEAR buttonand beginagain.
• If the oven temperaturewas previouslyadjusted,
Circuit Breaker the change will be displayed. For example, if the
temperature was reduced by 15°, -15 ° will be dis-
CANADIAN APPLIANCE ONLY played.
Your appliance is equipped with a circuit breaker box.
The box islocated either on a wall or in a cabinet nextto 4. Turn the SET knob to select the temperature change
or near the appliance. If part or all ofthe appliance does desired.
not operate, check to see if one of the breakers has
tripped. Reset the breaker to the ON position. • The oven temperature can be increased up to 35°
or reduced by as much as 35° (-35 °) in 5° incre-
O ments.
• NOTE: If you delay in selecting a temperature, the
program will automatically cancel and 00° will dis-
appear. Begin again if the programcancels.
O
5. Press the STOP/CLEAR button and the time of day
will reappear in the display.The oven will now bakeat
the adjusted temperature.
• O ,J It is not necessaryto readjustthe oven temperature if
there is a power interruption. This adjustment will not
affect broil or clean temperatures.
PAGE 16
To Next Page
Loading...
