Magnetrol Pulsar R96 Manual

Reference Conditions Reflection from ideal reflector at +70° F (+20° C)
Linearity ±0.3 inch (8 mm) or 0.1% of tank height (whichever is greater)
Measured Error ±0.3 inch (8 mm) or 0.1% of tank height (whichever is greater)
(Performance will degrade slightly within 60" (1.5 m) of antenna)
Resolution 0.1 inch or 1mm
Repeatability ±0.2 inch (5 mm) or 0.05% of tank height (whichever is greater)
Response Time <2 seconds (configuration dependent)
Initialization Time < 30 seconds
Ambient Temperature Effect Digital Horn Antenna: Average 0.12 inch (3 mm) / 10 K, max of ±0.4 inch (10 mm) over
the entire temperature range -40° to +175° F (-40° to +80° C)
Rod Antenna: Average 0.2 inch (5 mm) / 10 K, max of ±0.59 inch (15 mm) over
the entire temperature range -40° to +175° F (-40° to +80° C)
Analog Current Output (additional error with reference to 16 mA span)
Average 0.03% / 10 K. max 0.45% over entire temperature range
-40° to +175° F (-40° to +80° C)
Maximum Rate of Change 180 inches (450 cm)/minute
F
OUNDATION fieldbus
™
:
ITK Version 6.1.2
H1 Device Class Link Master (LAS) —selectable ON/OFF
H1 Profile Class 31PS, 32L
Function Blocks (6) Al, (2) Transducer, (1) Resource, (1) Arithmetic, (1) Signal Characterizer,
(2) PID, (1) Input Selector
Quiescent Current 17 mA
Execution Time 15 ms (30 ms PID Block)
Device Revision 01
DD Version 0x01
P E R F O R M A N C E
A N T E N N A S P E C I F I C A T I O N S
F U N C T I O N A L / P H Y S I C A L
T E M P E R A T U R E /
P R E S S U R E C H A R T
11
-50
(-45)
0
(-15)
0
100 (7)
200 (14)
300 (21)
400 (28)
500 (34)
600 (41)
700 (48)
800 (55)
50
(10)
100
(40)
150
(65)
200
(95)
250
(120)
300
(150)
350
(175)
400
(200)
450
(230)
Temperature ° F (° C)
Pressure psig (bar)
Polypropylene Rod
PTFE Rod & Horn
All-Polypropylene Flanged
All-Polypropylene Threaded and
Flanged ASME B31.1 & B31.3
All-Halar Threaded and
Flanged ASME B31.1 & B31.3
All-Halar Flanged
Model
Dielectric Rod
TFE
Dielectric Rod ➀
Polypropylene
Dielectric Rod
All-Halar
®
Antenna
3", 4", and 6" Horn
Materials
316 SS (Hastelloy
®
C, Monel
®
and
Kynar
®
opt.), TFE, Viton
®
O-rings
316 SS, Polypropylene,
Viton
®
O-rings
All-Halar, Viton
®
O-rings
316 SS (Hastelloy C and Monel
opt.), TFE, Viton
®
O-rings
Process Connection
1
1
⁄2" NPT and BSP, ANSI or
DIN flanges
1
1
⁄2" NPT and BSP, ANSI or
DIN flanges
1
1
⁄2" NPT and BSP, ANSI or
DIN flanges
6" ANSI or DIN flanges
Maximum Process
Temperature
+400° F @ 50 psig
(+200° C @ 3.5 bar)
+200° F @ 50 psig
(+95° C @ 3.5 bar)
+300° F @ atmos
(+150° C @ atmos)
+400° F @ 50 psig
(+200° C @ 3.5 bar)
Maximum Process
Pressure
-14.7 to 675 psig @ +70° F
(-1.0 to 46.5 bar @ +20° C)
-14.7 to 750 psig @ +70° F
(-1.0 to 51.7 bar @ +20° C)
-14.7 to 50 psig @ +70° F
(-1.0 to 3.45 bar @ +20° C)
-14.7 to 675 psig @ +70° F
(-1.0 to 46.5 bar @ +20° C)
Minimum Dielectric
(application dependent)
2.0 2.0 2.0 1.7 (1.4 with stillwells)
➀
Al
l-pol
ypropylen
e
constr
u
c
ti
on
opti
on
al
(se
e
c
ha
r
t
below for ratings)

Magnetrol Pulsar R96 Specifications

General

Brand	Magnetrol
Model	Pulsar R96
Category	Transmitter
Language	English