Why does the motor not run on my Makita DUR364L?
If your Makita Trimmer's motor doesn't run, it could be due to several reasons. First, make sure the battery cartridge is properly installed. If it is, the battery might be low or faulty; try recharging it or replacing it if recharging doesn't work. If these steps don't resolve the issue, the drive system may have a problem, requiring repair by an authorized service center.
What to do if the cutting tool does not rotate on my Makita Trimmer?
If the cutting tool on your Makita Trimmer isn't rotating, stop the machine immediately. Check for any foreign objects, like a branch, that might be jammed between the guard and the nylon cutting head, and remove them. If there are no obstructions, the drive system may not be working correctly, and you should seek repair from an authorized service center.
Why does my Makita Trimmer motor stop running after a little use?
If your Makita Trimmer stops running after a short period, there are a few potential causes. Check the direction of rotation and change it with the reversing switch if necessary. Also, the battery's charge level might be low, so try recharging it or replacing it if recharging isn't effective. Overheating can also cause this issue; if so, stop using the tool and allow it to cool down.
What to do if the cutting tool of my Makita DUR364L Trimmer does not rotate?
If the cutting tool on your Makita Trimmer isn't rotating, a foreign object, like a branch, might be jammed between the guard and the nylon cutting head. Remove the foreign object.
What to do if the cutting tool and motor cannot stop on my Makita Trimmer?
If the cutting tool and motor on your Makita Trimmer won't stop, immediately remove the battery. This indicates an electric or electronic malfunction that requires repair by an authorized service center.
What to do if my Makita DUR364L Trimmer has abnormal vibration?
If your Makita Trimmer is vibrating abnormally, stop the machine immediately. This could be happening because one end of the nylon cord has broken. Try bumping the nylon cutting head against the ground while it is rotating to cause the cord to feed. If the problem persists, the drive system may not be working correctly, and you should seek repair from an authorized service center.
Why does my Makita DUR364L Trimmer not reach maximum RPM?
If your Makita Trimmer isn't reaching its maximum RPM, it could be due to a few reasons. Ensure the battery cartridge is correctly installed as described in the manual. If the battery power is dropping, recharge it, and if recharging isn't effective, replace the battery. If these steps don't help, the drive system may not be working correctly, and you should consult an authorized service center for repair.
Why won't my Makita Trimmer motor run?
The motor of your Makita Trimmer might not be running because the battery cartridge isn't installed properly, so install the battery cartridge. Another reason could be a battery problem, such as undervoltage, in which case you should recharge the battery, and if that doesn't work, replace it.
What to do if Makita DUR364L Trimmer motor stops after short use?
If your Makita Trimmer's motor stops running after a short period, it could be due to the rotation being in reverse. Change the direction of rotation with the reversing switch. Alternatively, the battery's charge level might be low, so recharge the battery; if that doesn't help, replace the battery. Overheating can also cause this issue; stop using the tool to allow it to cool down.
Why is my Makita Trimmer not reaching maximum RPM?
Your Makita Trimmer might not be reaching maximum RPM because the battery is installed improperly; install the battery cartridge as described in this manual. Another cause could be dropping battery power, so recharge the battery, and if recharging isn't effective, replace the battery.
Details the essential protective gear to wear when operating the tool.
Guidelines and procedures for safely operating the cordless grass trimmer.
Critical safety advice for handling and using the battery cartridge.
Explains the integrated systems that protect the tool and battery from damage.
How to operate the power switch, adjust speed, and use the reverse function.
Detailed steps for replacing the nylon cutting line for different spool types.
General| Power Source | Battery |
|---|---|
| Battery Voltage | 36V |
| Motor Type | Brushless |
| Battery Type | Lithium-Ion |
| Max Cutting Speed | 6, 500 rpm |
| No Load Speed | 0 - 6, 500 rpm |
| Type | Brushless String Trimmer |
| Line Diameter | 2.0 - 2.4 mm |
| Spindle Size | M10 x 1.25 |
To Next Page
