EasyManuals Logo

Manitowoc National Crane 1300A User Manual

Manitowoc National Crane 1300A
92 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #75 background imageLoading...
Page #75 background image
National Crane Published 12-21-2011 CTRL #050-09 5-5
5
1300A OPERATOR’S MANUAL LUBRICATION PROCEDURE AND CHARTS
Internal Cable Sheave Lubrication
A grease gun adapter is required to lubricate the internal
sheaves. The required needle grease gun fitting is:
A 0.25 inch (6.35 mm) diameter nozzle grease gun tip
(National P/N 955045).
Contact Manitowoc Crane Care to obtain this tip.
Lubrication of the extend and retract sheaves is as follows:
1. Extend the boom until the grease access holes on the
side of the 2
nd
and 3
rd
sections are lined up.
2. Lubricate the pin for the extend cable sheaves (18)
(Figure 5-1) until a small amount of grease extrudes
from the pin. From in front of the boom, look back
through the sheave case at the pin to determine the
amount of grease.
3. This position also aligns the access holes in the rear of
the 1
st
and 2
nd
sections for lubrication.
4. Lubricate the pins for the retract sheaves until a small
amount of grease extrudes from the sheave pins. From
in back of the boom, look up through the winch mount at
the pins to determine the amount of grease.
Inner Boom Wear Pad Lubrication
1. Fully extend and set the outriggers.
2. With the boom fully retracted, remove the access
plate (6) located on the top rear of the 1
st
section
(Figure 5-2).
3. Apply grease to the wear pads on the top of the 2
nd
section through the access holes (4) in the 1
st
section
with a grease gun (Figure 5-2).
4. Extend the boom to line up the access holes on the 2
nd
section (3) with the wear pads on the 3
rd
section. Apply
grease to the 3
rd
section wear pads with a grease gun.
5. Extend the boom to line up the access holes (2) on the
3
rd
section with the wear pads on the 4
th
section. Apply
grease to the 4
th
section wear pads with a grease gun.
6. Raise the boom to at least 75°.
7. Extend the boom about 1/3 and retract to spread the
grease.
8. Repeat steps 3 - 6. Extend the boom about 2/3 and
retract to spread the grease.
9. Repeat steps 3 - 5. Fully extend and retract the boom to
spread the grease.
Side and Bottom Boom Wear Pad
Lubrication
1. Fully extend and set the outriggers.
NOTE: A fully extended boom at horizontal needs to have
an assist from a crane or forklift to retract. Lift the
front of the boom enough to relieve pressure on the
bottom wear pads. This should be sufficient for the
boom to retract.
2. Lower the boom to horizontal.
3. Fully extend the boom and apply grease to the side and
bottom of the 2
nd
,
3
rd
, and 4
th
sections with a brush.
4. Extend and retract the boom several times until the
grease is evenly spread.
5. Repeat steps 3 and 4 as necessary to ensure the boom
is fully lubricated.
19
Retract Sheaves: Extend the boom until the
retract sheave grease holes are visible through
the access holes along side of boom.
EP-3MG Grease Gun Weekly
20 Wire Rope (Extension Cables) WRL Spray or Brush
Any Time Boom is Disassembled or 5
Years
Item Application
Recommended
Lubricant
Procedure Frequency
DANGER
Do not, under any circumstances, work at an elevated
height without using proper fall protection as required by
local, state or federal regulations.
!
Reference Only

Table of Contents

Other manuals for Manitowoc National Crane 1300A

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Manitowoc National Crane 1300A and is the answer not in the manual?

Manitowoc National Crane 1300A Specifications

General IconGeneral
BrandManitowoc
ModelNational Crane 1300A
CategoryConstruction Equipment
LanguageEnglish

Related product manuals