Marantz PM-80 - Care and Maintenance

OPERATION PROCEDURES
TO PLAY AN ANALOG RECORD
1. Set the INPUT SELECTOR switch to PHONO.
2. Press the MM/MC switch according to the type of
cartridge (MM or MC) used on the turntable.
3. Play a record on the turntable.
4. Adjust the volume with the VOLUME control and adjust
the tone with the BASS and TREBLE controls.
NOTES:
@ Set the VOLUME control to the minimum position
before placing the stylus on the record or before
replacing the cartridge.
®@ Do not apply shock or vibration to the turntable during
play, as this may cause the stylus to jump and the
analog record to be damaged.
@ |fthe turntable is installed too close to the speakers, the
volume may not be able to be increased to a high level
due to howling.
@ Do not switch the power OFF while the stylus is on the
record surface.
TO LISTEN TO FM/AM BROADCASTS
1. Set the INPUT SELECTOR switch to TUNER.
2. Tune in the desired station on the tuner.
3. Adjust the volume with the VOLUME control and adjust
the tone with the BASS and TREBLE controls.
TO PLAY A COMPACT DISC
1. Set the INPUT SELECTOR switch to CD.
2. Play a CD on the CD player.
3. Adjust the volume with the VOLUME control and adjust
the tone with the BASS and TREBLE controls.
TO PLAY A COMPONENT CONNECTED
TO AUX 1/2 JACKS
The component connected to the AUX 1 or AUX 2 jacks on
the rear panel can be played as follows.
1. Setthe INPUT SELECTOR switch to AUX 1 or AUX 2.
2. Play the component connected to the selected input.
3. Adjust the volume with the VOLUME control and adjust
the tone with the BASS and TREBLE controls.
TAPE DECK OPERATION
TAPE PLAYBACK
1. Press the TAPE 1 monitor switch. The indicator above
the switch lights up.
2. Play a prerecorded tape on the tape deck.
3. Adjust the volume with the VOLUME control.
4. Adjust the tone with the BASS and TREBLE controls.
NOTES:
@ When not playing tapes, press the SOURCE switch (so
that the SOURCE indicator lights).
@ The tape can be played regardless of the setting of the
INPUT SELECTOR.
TAPE RECORDING
The playback sound of a program source component, such
as a turntable, a tuner, or a CD player, can be recorded on
tape as follows.
1. Set the INPUT SELECTOR switch to the program
source to be recorded.
2. Play the program source.
3. Operate the tape deck(s) to record the playback sound
on tape(s).
TAPE MONITORING
When a three-head tape deck is connected to the TAPE 1
jacks, the sound recorded on tape can be monitored
through the speakers by pressing the TAPE 1 monitor
switch. In this case, the tape deck must be connected to
this unit via both recording and playback connection cords.
NOTE:
When the tape deck is a two-head system, the recorded
sound cannot be monitored even when the TAPE 1
monitor switch is pressed. In this case, however, the sound
of the program source being recorded can be monitored.
DUBBING OF PRERECORDED TAPES
USING THE REC OUT SWITCH
For dubbing from tape to tape(s), set the REC SELECTOR
switch to TAPE COPY 1 — 2/3 or TAPE COPY 2 — 1/3.
Tapes can be copied regardless of the setting of the
INPUT SELECTOR switch.
NOTES:
@ To monitor the recorded sound, press the TAPE 1,
TAPE 2, or TAPE 3 monitor switch.
@ The program source selected with the INPUT SELEC-
TOR switch can be played during dubbing.
@ The tape in deck 1 can be copied on tapes in decks 2
and/or 3, or the tape in deck 2 can be copied on tapes in
decks 1 and 2.