Why does my Martin MAC 350 Entour Lighting Equipment fixture display CSER when powered on?
If your Martin Lighting Equipment fixture displays 'CSER' when powered on, this indicates a checksum error. Try uploading new software using the normal upload procedure. If the problem continues, upload the software using the boot mode upload procedure.
What to do if one or more Martin MAC 350 Entour fixtures resets incorrectly?
If one or more Martin Lighting Equipment fixtures resets incorrectly or responds erratically, inspect the data link connections and cables, correcting any poor connections and repairing or replacing damaged cables. Ensure the data link is terminated by inserting a termination plug in the output connector of the last fixture on the link. Also, check the fixture's DMX addressing and confirm it's set to the correct DMX mode. If issues persist, bypass each fixture one at a time by unplugging the XLR in and out connectors and connecting them directly together until normal operation is regained. Also check if the XLR pin-out on fixtures does not match (pins 2 and 3 reversed) and install a phase-reversing cable between the fixtures or swap pins 2 and 3 in the fixture that behaves erratically.
Why do pan and tilt freeze on my Martin MAC 350 Entour during reset?
If the pan and tilt freeze and FBER and EFHA messages are displayed during reset on your Martin Lighting Equipment, the reset cannot be completed because the effects hatch is not fully closed. Make sure that you close the effects hatch and start the reset again.
What to do if my Martin MAC 350 Entour fixture is completely dead?
If your Martin Lighting Equipment fixture is completely dead, first check the power supply and connections to ensure the fixture is receiving power. If the issue persists, disconnect the fixture from power and check the fuses. Replace any blown fuses.
What to do if LEDs cut out intermittently on Martin Lighting Equipment?
If the LEDs cut out intermittently on your Martin Lighting Equipment, the fixture may be overheating. Ensure free airflow around the fixture, clean it, and check that the ambient temperature does not exceed the maximum permitted level.
General| Color Mixing | CMY |
|---|---|
| Gobo Wheels | 2 |
| Iris | Yes |
| Zoom | Yes |
| Pan | 540° |
| Tilt | 270° |
| Control Protocol | DMX 512 |
| Type | Moving Head |
| Effects | Frost |
| Rotating Gobos | 7 rotating gobos |
Details safety precautions regarding electrical hazards and shock prevention measures.
Details safety measures to prevent burns and fire hazards associated with the fixture.
Outlines safety guidelines to prevent physical injury, particularly eye injury from LED light.
Provides instructions for removing the MAC 350 Entour from its packaging and lists included items.
Essential steps to follow before powering on the fixture for the first time.
Identifies and describes the various connectors on the fixture's connection panel.
Specifies the type, rating, and wiring requirements for the fixture's AC power cable.
Guides on installing the power connector and replacing mains fuses.
Instructions for safely connecting the fixture to AC power sources.
Provides tips for optimal DMX data integrity and cable selection.
Describes the physical connections required for DMX control and synchronization.
Instructions for securely attaching the fixture to a truss or rigging structure.
Explains how to use the control panel buttons and navigate through the fixture's menus.
Guides on configuring the fixture for DMX, stand-alone, or master/slave operation.
Details setting the DMX start address and selecting DMX modes (8-bit/16-bit).
Adjusting pan/tilt speed, display settings, and DMX reset behavior.
Configuring fan modes and selecting dimming curve profiles.
Managing custom settings and accessing information like software version and hours of use.
Operating the fixture manually and accessing service functions like tests and adjustments.
Tracking operating hours, monitoring temperatures, and viewing software versions.
Calibrating effects and understanding LED indicator functions.
Instructions for updating the fixture's firmware.
Details on shutter effects, intensity control, and color wheel functionality.
Information on the 6 rotating gobos, indexing, rotation, and shake functions.
Control over iris, focus, and the full range of pan/tilt movement.
Utilizing pre-programmed sequences and synchronizing them for chase effects.
Explanation of DMX modes offering different levels of control precision.
Managing fixture resets, speed control, and pan/tilt feedback via DMX.
Step-by-step guide to creating and storing scenes for independent operation.
Defines scenes, fade times, and wait times in stand-alone shows.
Capturing DMX effects into stand-alone scenes.
Setting up fixtures to synchronize shows in master/slave configurations.
Managing the service interval timer and alert system.
Details on using custom gobos, their orientation, and specifications.
Procedure for opening the effects hatch to access gobos and filters.
Guidelines for safely replacing gobos and color filters.
Detailed steps for removing and installing rotating gobos.
Procedures for calibrating focus, pan, and tilt for optimal performance.
Instructions for cleaning the fixture, including optical components.
Information on lubrication and steps for safely replacing the fixture's mains fuses.
Process for updating the fixture's operating software via a PC.
Methods for uploading firmware, including recovery for corrupted software.
DMX channel assignments for shutter effects, intensity, and color wheel functions.
DMX control for color wheel scrolling, rotation, and music-triggered chases.
DMX channels for selecting, rotating, and shaking gobos.
DMX channels for controlling the motorized iris and focus.
DMX channel assignments for controlling pan/tilt macro sequences.
DMX channel assignments for controlling effects macro sequences and their speed.
DMX channels for pan, tilt, and speed adjustments, including tracking/vector modes.
DMX control for effects speed, color settings, and gobo selection.
DMX channels for setting fixture parameters like fan mode and dimmer curve.
Configuring DMX address, operation modes, and pan/tilt speed.
Adjusting fan modes, dimming curves, display settings, and error reporting.
Enabling/disabling calibration and managing custom settings.
Managing stand-alone operation, saving/loading configurations, and resetting to defaults.
Accessing firmware version, fan speed, operating hours, and temperature data.
Menu items for controlling fixture attributes like reset, intensity, color, and gobos.
Menu items for pan/tilt movement, test sequences, and macro execution.
Capturing DMX scenes into stand-alone sequences.
Quick access functions via button combinations on the control panel.
Service functions for resetting, testing, and calibrating head components.
Procedures for calibrating focus, pan, and tilt for optimal performance.
Details on dimensions, effects capabilities, light source, and LED lifetime.
Information on DMX channels, protocols, stand-alone memory, and photometric data.
Details on gobo dimensions, materials, and recommended types.
Information on housing, mounting, power consumption, and thermal performance.
Safety certifications, included items, and available accessories.
Part numbers for spares, ordering information, and product disposal guidelines.
To Next Page