5
18
GGaass SSmmookkiinngg
1. Add desired amount of
wood in flame disk bowl.
2. Fill water bowl with
favorite marinade or
water. Do NOT overfill
water bowl. For dry
smoking do NOT use
marinade or water.
3. Place food on grill racks.
4. Remove lid and light
burner as outlined in
“Burner Lighting
Instructions” section in
this manual.
5. When burner is lit,
replace lid and adjust
flame to desired level.
CCaauuttiioonn::
•• SSmmookkeerr hheeaattss uupp qquuiicckkllyy..
•• SSmmookkeerr aacccceessss ddoooorr iiss
HHOOTT.. WWeeaarr pprrootteeccttiivvee
gglloovvees
s..
•• NNeevveerr mmoovvee ssmmookkeerr
wwhhiillee iinn uussee.. AAllllooww uunniitt
ttoo ccooooll ccoommpplleetteellyy bbeeffoorree
mmoovviinngg oorr hhaannddlliinngg..
GGaass GGrriilllliinngg
1. Remove smoker body and
water bowl. This allows
direct heat for grilling.
2. Remove lid and light
burner as outlined in
“Burner Lighting
Instructions” section.
3. When burner is lit,
replace lid and adjust
flame to desired level.
CChhaarrccooaall GGrriilllliinngg
1. Remove smoker body
and water bowl. This
allows direct heat for
grilling.
2. Add desired amount of
charcoal to flame disk
bowl.
3. Light charcoal following
directions on charcoal
bag.
OOrr uussee ggaass ccooookkeerr ttoo
lliigghhtt cchhaarrccooaall --sseeee ##33 iinn
CChhaarrccooaall SSmmookkiinngg sseeccttiioonn..
CChhaarrccooaall SSmmookkiinngg
1. Add desired amount of
charcoal to flame disk
bowl.
2. Light charcoal following
directions on charcoal
bag.
OOrr uussee ggaass ccooookkeerr ttoo
lliigghhtt cchhaarrccooaall --sseeee ##33..
3. Add charcoal to flame
disk bowl and place base
pan on cooker stand.
Light burner following
steps in “Burner Lighting
Instructions” section.
When charcoal is ready
turn OFF regulator control
valve and then gas
cylinder.
HOW
TO
SEASON AND USE
SMOKER
MMAASSTTEERRBBUUIILLTT RREECCOOMMMMEENNDDSS SSEEAASSOONNIINNGG SSMMOOKKEERR PPRRIIOORR TTOO FFIIRRSSTT UUSSEE..
• Follow burner lighting steps to light burner.
• Bring temperature up and maintain at 200°F(93°C).
• Place two or three wood chunks on flame disk bowl and
operate smoker with no food or water for two to four hours.
• Seasoning smoker will remove new smell.
TTeessttiinngg GGaass VVaallvvee::
• Turn gas cylinder valve ON and watch for bubbles. DO NOT LEAVE GAS ON MORE
THAN 12 SECONDS. If bubbles appear, stop, turn gas cylinder OFF and retighten fitting.
Repeat test.
TTeessttiinngg RReegguullaattoorr aanndd HHoossee::
• AFTER gas cylinder valve has passed Soapy Water Test, turn gas cylinder valve ON,
open regulator control valve one full turn and check for bubbles at valve location, along
full length of hose and at burner connection. DO NOT LEAVE GAS ON MORE THAN 12
SECONDS. If bubbles appear, stop, turn regulator valve OFF, turn gas cylinder OFF and
retighten the connection that is leaking gas. If hose is source of leak, STOP, do not use
unit. Hose must be replaced.
• When test is complete, and there are no leaks, wait a minimum of 5 minutes for gas fumes
to diminish before lighting cooker.
DDUURRIINNGG AANNYY PPOORRTTIIOONN OOFF SSOOAAPPYY WWAATTEERR TTEESSTT IIFF BBUUBBBBLLEESS C
COONNTTIINNUUEE TTOO
AAPPPPEEAARR,, SSTTOOPP,, DDOO NNOOTT UUSSEE UUNNIITT.. CCOONNTTAACCTT LLOOCCAALL PPRROOPPAANNEE DDEEAALLEERR OORR
MMAASSTTEERRBBUUIILLTT CCUUSSTTOOMMEERR SSEERRVVIICCEE 11--88000
0--448899--11558811..
NNoottee::
Use 20LB (9kgs) gas cylinder or smaller that has a protective collar with this unit.
Cylinder NOT included with this unit.
WWaarrnniinnggss::
• Soapy Water Test MUST be performed each time gas cylinder is connected to burner/hose
and/or each time it is used.
• Soapy Water Test MUST be performed outdoors in well ventilated area.
• When performing Soapy Water Test keep smoker away from open flames, sparks or lit
cigarettes.
• Smoker is designed to work with propane gas only. This product will NOT operate with natural
gas.
• Never use an open flame to test for gas leaks.
PPrreeppaarraattiioonn::
• Remove any cookware/smoker from cooker stand.
• Make sure regulator and gas cylinder valve is turned to OFF position.
• Prepare soapy water solution: (1) part dish washing liquid (or more if desired), (3) parts water.
• Apply soapy water solution to gas cylinder valve, regulator and hose length up to burner.
APPLY SOLUTION TO GAS
CYLINDER VALVE.
APPLY SOLUTION TO HOSE
REGULATOR AND THE FULL LENGTH OF
THE HOSE
.
APPLY SOLUTION TO UNDERNEATH CONTROL PANEL
WHERE BURNER AND HOSE ARE CONNECTED.
(
SMOKER SHOWN ON BACK FOR CLARITY ONLY)
FAILED TEST WILL PRESENT
BUBBLES AS SHOWN BELOW
SOAPY
WATER
TEST
WARNINGS & PROCEDURES
To Next Page
Loading...
Need help?
General
