What to do if LCB battery voltage is low on Matrix A5X-04?
If your Matrix Fitness Equipment displays 'LCB battery low voltage' (battery voltage < 11.2V), plug in the machine for AC charge and temporarily stop using the incline feature.
What to do if the incline is short circuited or over current in Matrix A5X-04?
If the incline on your Matrix Fitness Equipment is short-circuited or over current, check for misalignment of the Incline Motor, and replace it if necessary.
What to do if generator or resistor has an open or short circuit in Matrix Fitness Equipment?
If your Matrix Fitness Equipment's generator or resistor shows an open or short circuit, or if the current exceeds 3.7 Amps for 1 second, inspect the connections of both the generator and resistor. If necessary, replace either the generator or the resistor.
What to do if incline position has a difference of over 30% in Matrix A5X-04 Fitness Equipment?
If the incline position on your Matrix Fitness Equipment differs by over 30% and isn't reduced within 3 seconds, check for misalignment of the incline motor and replace it if needed.
What to do if the incline motor has no action or current in Matrix Fitness Equipment?
If the incline motor on your Matrix Fitness Equipment isn't working or doesn't have current, replace it.
What to do if there is a battery over charge current or battery short circuit in Matrix A5X-04?
If your Matrix Fitness Equipment displays a 'Battery over charge current' or 'battery short circuit' error, replace the LCB.
What to do if UCB has no communication response on Matrix Fitness Equipment?
If the UCB is not responding on your Matrix Fitness Equipment, check the connections of the console cable at both the console and the LCB. If necessary, replace the console cable (cc), the console, or the LCB.
Why is my Matrix Fitness Equipment resetting after 30 seconds due to RPM issues?
If your Matrix Fitness Equipment experiences RPM issues, and the unit resets after 30 seconds despite pedaling, verify that INCLINE RESET is in the on position in Manager Mode.
What to do if LCB is not getting power from the power receptacle in Matrix A5X-04 Fitness Equipment?
If the LCB on your Matrix Fitness Equipment isn't getting power from the power receptacle, check if LED 15 is lit on the LCB. If not, check for incoming AC voltage at the LCB.
What to do if LCB LEDs are lit, but there is no power to the console on Matrix A5X-04?
If the LCB LEDs are lit but there is no power to the console of your Matrix Fitness Equipment, check to see if LED 1 is lit on the upper control board.
General| Brand | Matrix |
|---|---|
| Model | A5X-04 |
| Category | Fitness Equipment |
| Language | English |
Details the location of the serial number on the Ascent Trainer.
Emphasizes reading and saving all safety instructions before operating the trainer.
Outlines the dedicated circuit and wire gauge requirements for the Ascent Trainer.
Provides guidance on cleaning the Ascent Trainer to prolong its life and appearance.
Advises on inspecting for worn or broken parts and using only genuine replacement components.
Details scheduled cleaning and maintenance tasks, including required tools and supplies.
Identifies and explains the functions of the various keys and displays on the Ascent Trainer console.
Guides users through setting up a manual workout, allowing custom input for resistance and time.
Explains how to set up the Fat Burn program, designed to help users burn fat through resistance changes.
Details setup for level-based programs like Rolling Hills and Interval Training.
Outlines the Cooper Fitness Test procedure for measuring cardiovascular fitness and estimating VO2.
Explains how to set up and use the Target Heart Rate workout mode for heart rate-controlled training.
Details the Constant Watts program, which adjusts resistance based on user-selected wattage goals.
Provides instructions for running the auto calibration procedure after installation or incline motor replacement.
Explains how club owners can access and customize the Ascent Trainer settings in Manager Mode.
Lists and describes the various customizable settings available within the Manager Mode.
Details how to enter and use Engineering Mode for advanced machine settings and diagnostics.
Explains how to access and utilize the various service functions available on the Ascent Trainer.
Presents detailed electrical diagrams for the Ascent Trainer components.
Lists and explains the error codes indicated by LEDs on the Lower Control Board (LCB).
Provides a table of console error codes, their descriptions, and recommended solutions.
Troubleshoots specific error codes (0140/01B2) related to incline motor operation.
Addresses troubleshooting steps for error code 01A0, indicating an incline motor disconnection.
Provides diagnostic steps for issues where the console is not receiving power.
Offers solutions for problems with the heart rate function not working or reading incorrectly.
Guides troubleshooting for RPM issues and when the console fails to record distance.
Introduces troubleshooting for TV and entertainment systems integrated with the Ascent Trainer.
Provides steps to resolve issues with fuzzy or unclear TV picture quality.
Offers solutions for when the integrated TV fails to power on.
Addresses problems related to the TV controller, keypad, or remote functionality.
Step-by-step instructions for removing and replacing the front disk assembly on the Ascent Trainer.
Details the procedure for removing and reinstalling the front shroud covers of the Ascent Trainer.
Provides instructions for replacing the Lower Control Board (LCB) on the Ascent Trainer.
Step-by-step guide for replacing the generator unit of the Ascent Trainer.
Instructions for replacing the generator belt on the Ascent Trainer.
Details the procedure for replacing the main drive belt of the Ascent Trainer.
Guides users through replacing the pulley axle set assembly.
Step-by-step instructions for replacing the drive axle set, noting the need for a special tool.
Provides instructions for replacing the crank assembly on the Ascent Trainer.
Details the process for removing and installing a new console unit.
Explains how to replace the console overlay and keypad.
Step-by-step guide to replacing the handlebar assembly on the console mast.
Provides instructions for removing and installing a new incline motor.
Details the procedure for replacing the dual action handlebar.
Instructions for removing and installing new foot pedals.
Step-by-step guide for replacing the pedal arm assembly.
Provides instructions for replacing the link arm.
Details the procedure for removing and installing a new swing arm.
Instructions for replacing the vertical stabilizer arm.
Step-by-step guide for replacing the incline arm cover.
Details how to service components attached to the handlebar, like buttons and grips.
Outlines the procedure for testing the Ascent Trainer after installation or part replacement.
Lists the technical specifications and features of the Ascent Trainer.
Details the hardware components required for assembling the Ascent Trainer.
Provides step-by-step instructions for assembling the Ascent Trainer unit.
Explains how to level the Ascent Trainer for optimal use and stability.
Provides instructions for installing an optional TV bracket onto the Ascent Trainer.
Details the steps required to upgrade the Ascent Trainer's console software using a USB drive.
To Next Page
