Meiko DV 125.2 - User Manual

Other manuals for Meiko DV 125.2

Installation Instructions8 pages

Questions and Answers

J
Jessica RowlandAug 19, 2025
How to reset factory setting parameter list on Meiko DV 125.2?
- D
  Dustin JohnsonAug 20, 2025
  To set parameters back to factory settings on your Meiko Dishwasher, switch the power supply OFF and then ON within 5 minutes.
D
David WoodsAug 21, 2025
Why does my Meiko Dishwasher say 'Emergency program active Restricted washing possible'?
- J
  Jacob Thomas Jr.Aug 21, 2025
  If the Meiko Dishwasher displays 'Emergency program active Restricted washing possible,' it indicates an issue with either the boiler/tank heating or the fresh water supply. Check the system to identify the exact cause.
S
Stephanie LopezAug 25, 2025
What does 'Regeneration in progress' mean on my Meiko DV 125.2 Dishwasher?
- S
  simpsonjosephAug 25, 2025
  The Meiko Dishwasher regeneration program has started and is currently running. You can pause the program, but you cannot cancel it.
L
Linda GoldenAug 26, 2025
What to do if my Meiko DV 125.2 Dishwasher says 'Regeneration necessary'?
- N
  ndudleyAug 26, 2025
  The Meiko Dishwasher requires regeneration. The user must start the regeneration by emptying the tank and adding salt.
S
steven69Aug 27, 2025
What to do if the hood of my Meiko DV 125.2 Dishwasher is not closed?
- S
  smithlonnieAug 27, 2025
  If the hood of the Meiko Dishwasher is not closed, check the connection S1, change the microswitch, check the microswitch adjustment or replace the defective I/O circuit board.
H
Heather SchaeferAug 29, 2025
What to do if my Meiko Dishwasher says 'Incorrect password / no authorization'?
- A
  audreydavisAug 29, 2025
  If you enter an incorrect password or lack authorization on the Meiko Dishwasher, enter the code once again.
T
taylorlisaAug 31, 2025
Why does my Meiko DV 125.2 Dishwasher say maintenance is required?
- K
  Kimberly MichaelAug 31, 2025
  Your Meiko Dishwasher indicates that maintenance is required because the set operating hours (P122) or batch number (P123) has been reached. Inform the service department and perform maintenance. After maintenance, reset the maintenance counter (P124).
M
Michael SaundersSep 2, 2025
What to do if my Meiko DV 125.2 hood is not closed?
- R
  Rachel EvansSep 2, 2025
  If the hood of your Meiko Dishwasher is not closed, you should check connection S1, check the microswitch adjustment, change the microswitch or replace a defective I/O circuit board.
T
Tracy YoungSep 4, 2025
What to do if my Meiko Dishwasher asks for factory setting parameter list?
- B
  Beverly LewisSep 4, 2025
  To address the 'Factory setting parameter list' message on your Meiko Dishwasher, switch the power supply ON/OFF within 5 minutes and set parameters back to factory settings. This action will be rejected, and parameters will be retained and Information 123 will disappear.
G
gregory54Sep 6, 2025
How to resolve the 'Incorrect password / no authorization' error on my Meiko DV 125.2?
- J
  John BrightSep 7, 2025
  To resolve the 'Incorrect password / no authorization' error on your Meiko Dishwasher, enter the code once again.