EasyManua.ls Logo

Midea WQP6-3705-AU - User Manual

Midea WQP6-3705-AU
26 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
Technical Service Guide
Compact Dishwasher 6 settings
MODEL SERIES: WQP6-3705-AU
IMPORTANT SAFETY NOTICE
The information in this service guide is intended for use by individuals possessing adequate backgrounds of
electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in personal
injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this
information, nor can it assume any liability in connection with its use.
WARNING
To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis
or test purposes, disconnect the power immediately after performing the necessary checks.
RECONNECT ALL GROUNDING DEVICES
If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for
service, they must be returned to their original position and properly fastened.
MIDEA CONSUMER PRODUCTS
TECHNICAL SERVICE GUIDE
COPYRIGHT. 2014
ALL RIGHTS RESERVED. THIS SERVICE GUIDE MAY NOT BE REPRODUCED IN WHOLE OR IN PART, IN ANY FORM, WITHOUT
WRITTEN PERMISSION FROM THE MIDEA DISHWASHER MANUFACTURING COMPANY.
CONTENTS
Introduction ............................................................................................................................................................. 3
Specification ........................................................................................................................................................... 3
Control Panel Features ......................................................................................................................................... 3
Component Locator Views ................................................................................................................................... 4
Dishwasher Components ..................................................................................................................................... 5
Main control board ......................................................................................................................................... 6
Floater assembly ........................................................................................................................................... 7
Heating pump motor assembly .................................................................................................................... 7
Heating pump assembly ............................................................................................................................... 8
Motor assembly .............................................................................................................................................. 9
Drain pump assembly ................................................................................................................................. 10
Check plate ................................................................................................................................................... 11
Inlet valve ...................................................................................................................................................... 11
Control panel ................................................................................................................................................ 12

Questions and Answers

  • L
    leroy20Aug 9, 2025
    What to do if my Midea WQP6-3705-AU Dishwasher shows an E4 Overflow error?
    • J
      Joseph DyerAug 9, 2025
      If your Midea Dishwasher displays an E4 error, indicating an overflow, there are several potential causes and solutions: - A failure may have occurred. Reconnect the wire of the Flooding Switch circuit and check again. - The Flooding Switch might be blocked. Check whether the Flooding Switch is blocked or not. - Improper detergent or rinse might be in use. Make sure you are using the proper detergent and rinse. - A failure may have occurred with the Drain Hose. Check the Drain Hose. - The Flowmeter circuit might not be correct. Check whether the Flowmeter circuit is correct or not. - There might be water at the bottom board. Remove the water from the bottom board and make sure there is no water at the bottom board.
  • F
    fowensAug 17, 2025
    Why does my Midea Dishwasher display an E3 error related to heating?
    • S
      Steven SummersAug 17, 2025
      If your Midea Dishwasher shows an E3 error, which means the heating time exceeded the pre-set limit, it could be due to several reasons: - The filter might be severely jammed. Check whether the filter is jammed severely or not. - There might be an issue with the overheat proof heating Micro-switch. Make a check of the over heat proof heating Micro-switch. - The Washing Pump circuit might be incorrect. Check whether the Washing Pump circuit is correct or not. - The NTC circuit might be incorrect. Check whether the NTC circuit is correct or not.
  • D
    Donald EdwardsAug 25, 2025
    What does E6 error mean on a Midea WQP6-3705-AU Dishwasher?
    • J
      Joseph BlevinsAug 26, 2025
      If your Midea Dishwasher displays an E6 error, indicating an open-circuit failure of the thermistor, you can try the following: - Check whether the NTC circuit is correct or not. - Reconnect the wire of the Flowmeter circuit and check again.
  • G
    gregory03Sep 1, 2025
    What to do if Midea Dishwasher shows E7 error?
    • A
      Andrea StewartSep 1, 2025
      If your Midea Dishwasher displays an E7 error, indicating a short-circuit failure of the thermistor, you can try the following: - Check whether the NTC circuit is correct or not. - Reconnect the wire of the Flowmeter circuit and check again.

Summary

Main control board

Floater assembly

Heating pump motor assembly

Heating pump assembly

Motor assembly

Drain pump assembly

Inlet valve

Control Panel

Operating board

Dispenser

Door Lock Assembly

Air breaker

Test program

How to activate Test Program

Detailed steps and button combinations to enter the test program mode.

Procedure of Test Program (for models controlling water filling by flowmeter)

Outlines test program steps, screen displays, and descriptions for flowmeter models.

Troubleshooting

E1 Water filling exceed pre-set time

Describes the causes and actions for error code E1 related to water filling time.

E3 Heating exceed pre-set time

Explains error code E3, indicating issues with the heating element's performance.

E4 Overflow

Details error code E4, which signals an overflow condition in the dishwasher.

E6 Open-circuit failure of thermistor

Describes error code E6, pertaining to an open-circuit failure in the thermistor.

E7 Short-circuit failure of thermistor

Explains error code E7, indicating a short-circuit failure in the thermistor.

E1 Tree

E3 Tree

E4 Tree

E6-E7 Tree

Midea WQP6-3705-AU Specifications

General IconGeneral
Capacity6 place settings
Energy Star QualifiedNo
ColorWhite
Noise Level49 dB
Delay StartYes

Related product manuals