EasyManua.ls Logo

Midea WQP6-3603A - User Manual

Midea WQP6-3603A
22 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Lave vaisselle ELVC 491B
1
Technical Service Guide
Compact Dishwasher
6 settings
MODEL SERIES:
WQP6-3603A
IMPORTANT SAFETY NOTICE
The information in this service guide is intended for use by individuals possessing adequate backgrounds of
electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in personal
injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this
information, nor can it assume any liability in connection with its use.
WARNING
To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis
or test purposes, disconnect the power immediately after performing the necessary checks.
RECONNECT ALL GROUNDING DEVICES
If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for
service, they must be returned to their original position and properly fastened.
MIDEA
C
ONSUMER
P
RODUCTS
T
ECHNICAL
S
ERVICE
G
UIDE
COPYRIGHT.
2014
A
LL RIGHTS RESERVED
.
T
HIS SERVICE GUIDE MAY NOT BE REPRODUCED IN WHOLE OR IN PART
,
IN ANY FORM
,
WITHOUT
WRITTEN PERMISSION FROM THE MIDEA DISHWASHER MANUFACTURING
C
OMPANY
.
CONTENTS
Introduction ............................................................................................................................................................. 3
Specification ........................................................................................................................................................... 3
Control Panel Features ......................................................................................................................................... 3
Component Locator Views ................................................................................................................................... 4
Dishwasher Components ..................................................................................................................................... 6
Main control board ......................................................................................................................................... 6
Floater assembly ............................................................................................................................................ 7
Heating pump motor assembly .................................................................................................................... 7
Heating pump assembly ............................................................................................................................... 8
Motor assembly .............................................................................................................................................. 9
Drain pump assembly ................................................................................................................................. 10
Check plate ................................................................................................................................................... 11

Questions and Answers

  • S
    scott76Aug 11, 2025
    What to do if my Midea WQP6-3603A will not pump out water?
    • A
      Ashley DayAug 11, 2025
      If your Midea Dishwasher isn't pumping out water, several factors could be responsible: * A defective drain pump might be the cause, requiring replacement. * The drain hose could be obstructed; check the drain hose. * The PCB assembly might be defective, necessitating replacement. * Damaged or defective wiring could be the issue; repair the wiring.
  • B
    Billy FrazierAug 17, 2025
    What to do if my Midea WQP6-3603A does not work when I press start?
    • S
      sonia50Aug 17, 2025
      If your Midea dishwasher doesn't start when you press the start button, it could be due to: * The door not being closed properly; ensure the door is fully closed. * Defective door switch contacts; replace the door switch. * A defective door handle assembly; replace the door handle assembly. * Damaged or defective wiring; repair the wiring. * A defective PCB assembly; replace the PCB assembly.
  • R
    Robin SimonAug 29, 2025
    What does error code E4 mean on my Midea WQP6-3603A (overfall alarm)?
    • C
      courtneycarterAug 29, 2025
      If the Midea Dishwasher LED displays 'E4', it indicates an overfill alarm. This can be caused by: * A defective micro-switch for overfall safeguard: Replace the micro-switch. * Damaged or defective wiring: Repair the wiring. * A defective PCB assembly: Replace the PCB assembly. * Water leaks from the dishwasher: See “Water leaks from dishwasher”.
  • T
    Tammy KellySep 4, 2025
    Why is my Midea WQP6-3603A running but not heating the water?
    • T
      Thomas TaylorSep 4, 2025
      If your Midea Dishwasher runs but doesn't heat, consider the following potential causes: * Low input voltage: The lowest input voltage should be 198V. * A defective thermal resistor: Replace the thermal resistor. * Damaged or defective wiring: Repair the wiring. * Too little water fill: See “Too little water fill.” * A defective micro-switch of the pressure switch assembly: Replace the micro-switch of the pressure switch assembly. * A defective heating element: Replace the heating element. * A defective PCB assembly: Replace the PCB assembly.
  • J
    James PriceNov 22, 2025
    Why does my Midea WQP6-3603A show error code E1 and not fill with water?
    • J
      Jason CohenNov 22, 2025
      If the Midea Dishwasher LED shows 'E1', it indicates the dishwasher isn't filling with water properly. This could be due to several reasons: * The water supply might be off; in this case, turn it on. * There might be low water pressure; ensure a minimum of 20 PSI. * The water fill valve could be defective and needs replacement. * The water fill valve or hose could be obstructed, requiring disassembly and cleaning. * Wiring might be damaged or defective, needing repair. * The pressure switch for high water level safeguard could be defective and needs replacement. * The flowmeter might be defective and needs replacement. * Heavy water usage elsewhere in the home can affect the dishwasher's water supply; try using the dishwasher when water usage is minimal. * The PCB assemb...

Midea WQP6-3603A Specifications

General IconGeneral
Capacity6 place settings
Energy Efficiency ClassA
Noise Level49 dB
Washing Performance ClassA
Drying Performance ClassA
Half Load OptionYes
Water Pressure0.04-1 MPa
Power Supply220-240V/50Hz
Wash Programs6 (Intensive, Normal, Economy, Glass, Rapid, Soak)
Delay StartYes (3, 6, 9 hours)

Related product manuals