EasyManua.ls Logo

Midea WQP6-3602E Series - User Manual

Midea WQP6-3602E Series
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
Technical Service Guide
Compact Dishwasher （6 settings）
MODEL SERIES: WQP6-3602E
IMPORTANT SAFETY NOTICE
The information in this service guide is intended for use by individuals possessing adequate backgrounds of
electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in personal
injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this
information, nor can it assume any liability in connection with its use.
WARNING
To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis
or test purposes, disconnect the power immediately after performing the necessary checks.
RECONNECT ALL GROUNDING DEVICES
If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for
service, they must be returned to their original position and properly fastened.
MIDEA CONSUMER PRODUCTS
TECHNICAL SERVICE GUIDE
COPYRIGHT. 2014
ALL RIGHTS RESERVED. THIS SERVICE GUIDE MAY NOT BE REPRODUCED IN WHOLE OR IN PART, IN ANY FORM, WITHOUT
WRITTEN PERMISSION FROM THE MIDEA DISHWASHER MANUFACTURING COMPANY.
CONTENTS
Introduction ............................................................................................................................................................. 3
Specification ........................................................................................................................................................... 3
Control Panel Features ......................................................................................................................................... 3
Component Locator Views ................................................................................................................................... 4
Dishwasher Components ..................................................................................................................................... 5
Main control board ......................................................................................................................................... 6
Floater assembly ........................................................................................................................................... 7
Heating pump motor assembly .................................................................................................................... 7
Heating pump assembly ............................................................................................................................... 8
Motor assembly .............................................................................................................................................. 9
Drain pump assembly ................................................................................................................................. 10
Check plate ................................................................................................................................................... 11
Inlet valve ...................................................................................................................................................... 11
Control panel ................................................................................................................................................ 12

Table of Contents

Questions and Answers

  • S
    Stephen LucasAug 20, 2025
    Why is my Midea WQP6-3602E Dishwasher leaking water?
    • B
      Brian HendersonAug 20, 2025
      If you're experiencing water leaks from your Midea Dishwasher, potential causes include too much water fill, a defective drain pump, the dishwasher not being level, soap suds leaking, loose hose clamps, a loose overflow cover, the drain pump assembly not seated properly, or defective flow system seals. Consider leveling the dishwasher, tightening or replacing hose clamps, remounting the overflow cover or drain pump assembly, or replacing the flow system seals.
  • E
    evargasAug 22, 2025
    What to do if Midea Dishwasher will not pump out?
    • A
      Ariana SimonAug 22, 2025
      If your Midea Dishwasher is not pumping out water, possible causes include a defective drain pump, an obstructed drain hose, damaged wiring, or a defective PCB assembly. You should check the drain hose and consider replacing the drain pump or PCB assembly, or repairing the wiring.
  • V
    Victor FarrellAug 25, 2025
    What to do if Midea Dishwasher does not work when press start?
    • S
      Stephanie BanksAug 25, 2025
      If your Midea Dishwasher doesn't work when you press start, make sure the door is fully closed. Other potential issues include defective door switch contacts, a defective door handle assembly, damaged wiring, or a defective PCB assembly. You may need to replace the door switch or door handle assembly, or repair the wiring.
  • R
    Robert HernandezAug 26, 2025
    Why water remains in bottom of Midea WQP6-3602E Dishwasher?
    • P
      Paul ChavezAug 26, 2025
      If you notice water remains in the bottom of your Midea Dishwasher, a small amount of water in the sump area is normal to keep the pump primed and is drained automatically at the beginning of each cycle. However, excessive water could indicate a defective drain pump, a defective check plate, or a defective one way valve. Consider replacing the drain pump, or cleaning or replacing the check plate or air breaker.
  • B
    Brandi SanchezAug 28, 2025
    How to fix Midea Dishwasher that will not fill with water?
    • B
      Betty McculloughAug 28, 2025
      If your Midea Dishwasher isn't filling with water, first, ensure the water supply is turned on. Check for low water pressure, which should be a minimum of 20 PSI. Inspect the water fill valve and hose for any obstructions, disassembling and cleaning them if necessary. Other potential causes include a defective water fill valve, damaged wiring, a defective pressure switch, a defective flowmeter, heavy water usage elsewhere in your home (try using the dishwasher when water usage is minimal), or a defective PCB assembly.
  • T
    tammypattonAug 30, 2025
    Why Midea Dishwasher runs with door open?
    • J
      Jason HamiltonAug 30, 2025
      If your Midea Dishwasher runs with the door open, it could be due to defective door switch contacts, a defective door lock assembly, damaged wiring, or a defective PCB assembly. Consider replacing the door switch or door lock assembly, or repairing the wiring.
  • M
    Mr. John ArnoldSep 1, 2025
    What causes Midea WQP6-3602E motor to hum but not start?
    • E
      Elizabeth ConnerSep 1, 2025
      If your Midea Dishwasher motor hums but won't start, it could be due to defective motor bearings, a defective motor capacitor, damaged wiring, or improper motor voltage. You may need to replace the motor or motor capacitor, or repair the wiring.
  • D
    dennisbaileySep 2, 2025
    How to fix Error E3 Midea Dishwasher runs but will not heat?
    • B
      Brandon ChenSep 2, 2025
      The error E3 on your Midea Dishwasher, indicating it runs but won't heat, can be due to several reasons: low input voltage (the lowest input voltage is 198V), a defective thermal resistor, damaged wiring, too little water fill, a defective micro-switch of the pressure switch assembly, a defective heating element, or a defective PCB assembly. Consider replacing the thermal resistor, micro-switch, heating element, or PCB assembly, or repairing the wiring.
  • T
    Tina NguyenSep 4, 2025
    Why my Midea Dishwasher runs repeated cycles?
    • M
      michael53Sep 4, 2025
      If your Midea Dishwasher experiences repeated cycles, it might be due to a defective PCB assembly. Consider replacing the PCB assembly.
  • M
    Michael BrownSep 6, 2025
    Why Midea WQP6-3602E Dishwasher motor trips out on internal thermal overload?
    • W
      William GrantSep 6, 2025
      If your Midea Dishwasher motor trips out on internal thermal overload, it could be due to shorted motor windings, improper motor voltage, or a defective motor capacitor. Consider replacing the motor or motor capacitor.

Summary

Introduction

Specification

Control Panel Features

Control Panel Overview

Details the functions of buttons, indicators, and the display on the dishwasher's control interface.

Component Locator Views

Front View Identification

Illustrates and labels the external components visible from the front of the dishwasher.

Interior View Identification

Shows and labels internal components, such as baskets and dispenser, within the dishwasher.

Dishwasher Components

Main control board

Explains the main control board's function and its removal/replacement procedures.

Floater assembly

Details the floater assembly, its role, and the steps for its service.

Heating pump motor assembly

Covers the heating pump motor assembly, including its removal and replacement.

Heating pump assembly

Describes the heating pump assembly, its components, and service instructions.

Motor assembly

Outlines the motor assembly, its parts, and the process for its removal and replacement.

Drain pump assembly

Details the drain pump assembly and the procedures for its removal and installation.

Check plate

Explains the check plate, its function, and the replacement process.

Inlet valve

Covers the inlet valve, including its removal and installation procedures.

Control panel

Describes the control panel, its function, and the steps for its removal and installation.

Operating board

Details the operating board, its location, and the procedure for its removal and replacement.

Outer Door

Explains the outer door and the process for its removal and installation.

Dispenser

Details the dispenser's operation and the steps for its removal and replacement.

Inner Door

Describes the inner door and its removal/replacement process.

Shell

Provides instructions for removing and installing the dishwasher's outer shell.

Door Lock Assembly

Details the door lock assembly, its function, and removal/replacement procedures.

Air breaker

Explains the air breaker, its role, and the steps for its removal and installation.

Hinge assembly and Spring system

Covers the hinge assembly and spring system, including their removal and replacement.

Tank assembly

Describes the tank assembly and the procedure for its installation and removal.

Troubleshooting

Midea WQP6-3602E Series Specifications

General IconGeneral
BrandMidea
ModelWQP6-3602E Series
CategoryDishwasher
LanguageEnglish

Related product manuals